36348 Kenmore - Instructions

The problem with this model is usually a burned out heater assembly, when the freezer is still freezing, but the fresh food section is warm. To check, first disconnect power from refrigerator. Remove food and then shelves from freezer section. Remove the screws that hold the back freezer panel in place. Remove back panel and the coil ... Read more s will be exposed. If they are covered in ice the heater is most likely the problem. At the bottom of the coils below the heater assembly is a drain hole plug this hole with a rag. Place a large towel in bottom of freezer pan beneath the coils to catch the water. I do not recommend any method to melt the ice from the coils but a hair dryer, do not chip at the ice or you will most likely damage the coils. After you have defrosted the coils and removed all water from the unit, remove the two screws that hold the heater element in place, this element is directly below the coils. Look at the element, if it is burnt black, this is a tell tale sign it is bad. If that is the case it will need to be replaced. Remove the electrical wires located on te end of unit, the new unit will have instructions with it, reconnect the electrical wires per instructions, remount heater with the same mounting screws that held it in place. Be sure to remove rag from drain hole, replace back freezer panel with screws, replace shelves, and plug refrigerator back in. If your problem was a cold freezer section but a warm fresh food section this should fix your problem. In conclusion, this problem and the fix for it is indicative to these model's ge refrigerator's

First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.

Troubleshooting was easy - others had the same problem - coils freeze over and frost blocks air flow to refrigerator - part identification made easier by online picture - many parts look the same so you may want to call and confirm before you order (there were variations to this model number) - To repair: take off five screws that hold t ... Read more he metal panel on the back of the freezer - remove the panel - use a heat gun or hair dryer to melt ice from the coils (put a towel at the bottom to soak up the water) - unplug the kit at the top of the freezer and carefully pull off the thermostat clipped to the coil - remove the four screws that hold the heater kit to the back of the freezer - install the new kit where the old one was then re-install the panel to the back of the freezer - next, make time to clean the condenser coils under the refrigerator/freezer

Couldn't find schematic or repair manual
Finally found your site which showed the location and part numbers of the timer and heaters.
I ordered them; they came immediately.
I replaced only the timer, since it was the easiest and took only a few minutes. Defrosting the frezer coils with a hair dryer took about an hour.
... Read more >Rerigerator froze over again in about two weeks.
I then replaced the heaters. One of the heaters was 'open circuit'.

I read over the other posts here and went with jacking up the fridge door and setting it on (2) 2x4 studs. A nut driver was used to remove the bottom hinge. I then drilled out the rivet that held the old cam in place and then used a 3/16 rivet to secure the new cam. A rivet is not necessary as you can also use a nut and bolt to hold the c ... Read more am in place. It took less time to order the part and install it than it did to drive over to the appliance parts store and pick it up. I ordered around 10 am and the part was here the next day at 2:00 (without special delivery costs). By 2:30 it was on my fridge.

First, I made a mistake. I took all the screws out and removed the gasket. This allowed the door tray to drop loose. Then, I realized that wasn't the way to go. So I remounted the door tray and the metal gasket supports but left the screws loose. Then, starting at the top, I worked the new gasket in behind the metal supports and tigh ... Read more tened the screws along the way. I completed the installation by following this same method down the sides and at the bottom.

Shut off power to the refrige. Removed old icemaker, using large hammer. Installed new unit.

This is a sibe-by-side refrigerator/freezer that needed a new lower hinge set for the fridge door.

First I removed everything from inside the fridge door, closed it, then loosened the top hinge bolts with an 8mm socket on a 1/4-inch ratchet. Using an 8mm nutdriver, I removed one bolt and loosed the other just far enough to be ... Read more able to lift the hinge and swing it out of the way. (These bolts are long. The nutdriver is faster than the ratchet but you need a ratchet or a wrench to first break them loose.) Then I just lifted the door off the bottom hinge and set it aside.

The plastic lower front grill was covering the lower hinge but that grill is just held at the ends by spring clamps -- popped off easily so I could get to the hinge bolts. Again, 8mm bolts, just remove & replace hinge. I also had to replace the upper half of the door closer cam, which is screwed to the bottom of the door, being careful that the holes lined up: cam, shim, door holes.

Now the tricky part was lifitng the door back on the lower hinge. (It helps to have an assistant at the bottom to locate the hole for you.) Once the door was up, I swung the top hinge over, ran the two bolts in finger tight with my nutdriver, checked & adjusted the spacing* of the fridge door and tightened the bolts. This was all very easy! (*^_^*)

*On a side-by-side, you'll want the door to be straight up & down with a consistent gap top to bottom with the freezer door. The hinge has some slack for adjustment by positioning the door, then tightening the bolts. You'll see what I mean.

1. Unplug, remove control knob from both temp control sliders, remove upper light bulb and light shield from refrigerator compartment. 2. Remove screw holding top of bracket control mod in place. 3. Lift bottom tab from slot and remove control mod from ref compartment. 3. Unplug temperature control and defrost timer and replace. (Each are ... Read more held in place with two screws.) 4. Replace control mod. This part took me the longest because the space between the top of the control mod and the top of the ref. compartment is very small and replacing the nut was difficult. Use a nut driver with a long shaft. 5. Use screw driver to turn control button of defrost timer to start cycle. 6. Replace bulb cover and light bulb. 7. Set temp control to initial setting. 8. Have a Margarita and celebrate. It's been over a week and the refrigerator/freezer is working perfectly.

First I removed the oven door from the appliance. Then I placed it on a table and removed the screws from around the edges. First I removed an aluminum heat shield. Then I removed the first of three heat shielding glass viewing panels, followed by the second one by removing even more screws. I carefuly laid the parts out in the oreder ... Read more that I remove them along with their screws. Next I removed the large heat shielding aluminum plate that held the first two glass heat shields. Then removed a layer of insulation. Then I was down to the sheel steal plate that holds the gasket. As a precaution I removed the thick pyrex glass heat shilding viewing panel. Lastly the plate that held the door seal was removed. After removing the old gasket, I carefully placed the new oven door gasket in place. After cleaning all the parts that had been removed, I replaced them one at a time in reverse order. Most of my time was spent cleaning. How ever I was especially impressed with the good condition of the oven door after 20 years of approximately every other day oven use. Thanks

I removed the shelf, unscrewed the slide rails and replaced them with new ones. I replaced the shelf, put the food back in and I was done. Thanks, john bowers

removed 4 screws of the back fan cover, then removed the two screws holding the element and disconnected the slip-on electrical wire connections. replaced enement and cover in reverse. this was all done after i cut power at circut breaker duhh

I removed the two mounting screws then pulled the element forward and disconnected the two element screws. I reversed the process to install the new one/ this oven is over 30yrs old.

First unplug the refrigerator!

Removed the top shelf of the refrigerator. Pulled off the knobs from the temp slider controls. Popped the cover off of the light and temp control section. This Hotpoint model has both
thermostat and defrost timer easily accessible in the refrigerator compartment. Used a socket set
dr ... Read more iver to loosen the screws and remove the
temp control section and unplugged the wire connectors. This freed the whole temp control
section. On the workbench removed the old
thermostat by unscrewing the screws with a socket driver. Unplugged the wires from the old thermostat then put the new one in. Then put the
new one in the same holes, reconnected the
wires and reassembled the everything. Then
simply put this temp control box back in the
original place (and reconnect the wire plugs)
and put the screws back in . The hardest part is re-aligning the holes and the control levers, but this is not too bad.

Plugged it back in and so far it has been turning
on and off normally. (The old thermostat contacts
were oxidized so I think this was the problem).

New ice maker only used 2 screws and the old one had 3. This was no problem. The old ice maker had already been removed. Just loosen the 3 screws and unplug the cord to ice maker. Only problem with ice maker was with the cord, which I had to use the supplied adapter. It was too long and in the way when reinstalling the ice bin. The ice b ... Read more in had a small notch area on the bottom left. I used a plastic tie to bundle the cord into the notch. Carefully placed ice bin and no problem. The first part I received was damaged and was replaced 2 days later by a brand new part. Customer service charged for the replacement part but said they would credit my charge card within 2 to 3 weeks for the damaged part. Its been a week and if they follow thru like the said I woild give Part Select 5 Stars for service and Parts.