3627538 Kenmore Range - Instructions

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

first i removed the screws that held the element and put the other one on. still would not heat . so i took the back of stove ,sides of stove loose to trace wires and under the top of stove i found a wire that comes from oven switch had been bitten into by a mouse wire nutted and electrical taped the wire back togeather and it workes fi ... Read more ne . keep in mind there are 3 thinge that could be wrong. it goes from the switch, to the gas valve in broialer to the igniter switch,gas,fire .

I removed the whole burner (3 screws) and the igniter (2 screws). IGNITER comes from Mfg. boxed with wrong plug on igniter - however they supply two porclean nuts so that the wires can be cut and joined. I recommend that you use the plug off the old igniter and splice it to the new part, so that it will plug into the stove's existing plu ... Read more g

Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cav ... Read more ity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix ... Read more whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all.
T.Melillo

Take out inside of oven.Igniter is held on with 2screws and electrical clip.take off old one and put on new one.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats g ... Read more ood now, makes great cornbread and biscuits, the wife helps the oven do this.

While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new line ... Read more s came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I thought that when the burner didn't light it was the control valve at fault. After shutting off the gas, I changed the valve by removing the wires, undoing the tubing, then unscrewing the unit from the back of the unit. This worked one time. It turns out that if there isn't enough voltage from the burner, the valve won't open. I found ... Read more this out after I mistakenly thought that the new valve was faulty. Check the voltage from the burner before you do anything else.

From back, top of stove, removed 4 screws from panel to gain access to control unit. Removed 4 screws holding control and let hang from wires. Removed face plate from old unit and installed on new part. Installed new control and one at a time removed wires from old part and connected to new control. Replaced cover panel. Oven works fine n ... Read more ow.

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 yea ... Read more r old oven,it was very easy/.