36274 Kenmore Range - Instructions

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it f ... Read more its snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and disc ... Read more ard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

Not a repair - just a replacement. Very easy. Just remove the grates, lift out the drip pans, replace with the new drip pans, and replace the grates. As the size of the holes vary you just have to make sure that they are lined up correctly. I was delighted to find that replacements were available for a range I've had for 14 years. ... Read more The range itself still works great. Thank you for your promptness in sending the replacements. I highly recommend your service.

Took longer to open the box.

I unscrewed to old glide and replaced it then re attached the screw

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

On each side of the door at the top you will find an allen screw, remove those to remove the cover plate. This will prevent the new glass from sitting flush with the door, if not removed. On the inside of the door, you will find two more silver hex screws, these release the glass frame. On the flimsy part that seperates from the main door ... Read more frame, there are two small brackets that hold the glass panel at the bottom of the door. Carefully pry out all the ramaining glass shards, and believe me they are there, so be very careful and vacuum up immediately to prevent cuts later. The glass frame will be very wobbly, so position yourself in front and place one knee up to support the frame and place the new glass panel in the bottom slot first, then just hold it up, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. Now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame.My oven door handle never had to come off.

Replaced old with new.

slid the old ones out and slid the new ones in. done

Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.

Order parts and installed - no tools needed - completed repairs less than 1 minute