3627272 Kenmore Range - Instructions

My husband and I simply took the burner units out of the packing, took the old ones off, put the new ones in. The new units needed to be leveled, but the leveling nuts included fit perfectly, and the entire repair took less than 15 minutes.

Followed previous posts, just took out the metal pan (2) 1/4" head screws. Removed the ignitor bracket (2) 1/4" head screws. Disconnected the existing ceramic wirenuts. Removed the ignitor from the bracket......this was the hardest part as the self threading screw stripped out in the sheet metal. Took some time to remove that screw an ... Read more d re-tap the hole to #10-32. Once that was done used a #10-32 x 1/2" machine screw with lock washer. All went back together fine from there.

I put the grates in backwards and the wife had to turn them around after teasing me about it......maybe I should do more baking.......

My Hotpoint gas oven became extremely hot after using it . Only after unplugging the electrical cord, turned it off. Replacing the control valve (thermostat) solved the problem. The stove top had to be pried up with a flat screw driver then propped up. Prying off the oven control valve revealed two mounting screws (philips ... Read more head). Next remove thermostat sensor bulb inside oven at back wall. Remove old thermostat control and bulb assembly. Installation is reverse order of disassembly.

removed the gas burner which allowed easy access to undo the old igniter.
opened the wire hatch in the back of the oven cavity, and also took off the cover (two screws) on the back panel to allow access to the igniter connector.
I cut the wires to the old igniter, leaving lots of wire, stripped the wire, and then hooked up the n ... Read more ew igniter using the supplied ceramic / hi-temp twist on connectors.
then just closed up everything in reverse.
helps to take off oven door, and you need access to the back side of the oven.

I turned off the gas flow to the appliance, removed the old oriface spuds with the adjustable wrench, inserted the new oriface spuds and tightened them with the adjustable wrench. The double burner assembly just dropped on. They fit perfectly. I did not have to use the leveling nuts that were included with the burners. The old levelers we ... Read more re still in place and set perfectly for the new burners. Very easy repair, and the range works like a new one.

0) Unplug oven and shut off gas at the valve behind oven.
1) removed oven door (no tools required)
2) Removed enamed steel oven bottom (2 thumbscrews, push back, pull out)
3) Removed base panel on outside of oven (some might have a warming or storage drawer)
4) From bottom, removed heat shield to allow access to unders ... Read more ide of igniter -- 4 sheet metal screws, use 1/4" nutdriver
5) Now you should see all of the igniter, along with its wiring. One lead goes to a spade lug, the other uses a white nylon connector. Unplug igniter.
6) Using 1/4" nut driver, unscrew igniter from below. This is probably the toughest part of the job.
7) Once igniter is removed, put the bad igniter and the new igniter side by side. The leads on the replacement igniter are probably not going to be long enough (I ran into this), so clip the leads from the old igniter at the bas of the igniter and splice into the leads from the new igniter. After stripping the lead ends, I used a barrel splicer, but a wire nut or an inline splice with some heatshrink tubing or cloth electrical tape should also work fine.
8) Reverse steps above to install.

The igniter apparently controls the gas flow, so if the igniter doesn't get hot, the gas won't flow. In other words, be careful, but don't worry too much about having to worry about gas leaks, etc. In the end, it wasn't all that difficult, but I'm pretty good at home repair stuff. If you have a hard time plugging in a toaster, you should probably call a repairman.

The R&R of the defective thermostat was at first look relatively simple. The job was made more complicated because in order to remove the old thermostat and then route the new thermostat across the top of the stove, under the burners, and down through a small hole into the oven space I had to remove the whole top of the stove. This proce ... Read more ss is not hard, just time consuming. Be very careful of razor sharp edges, they make you bleed. The final calibration of the oven is an easy adjustment in the oven knob. All in all it was an good experience.



Lyle Nelson

my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.

IF YOU DONT FEEL COMFORTABLE WORKING WITH NATURAL GAS APPLIANCES PLEASE CONTACT A REPAIR MAN. TURN OFF GAS LINE FEEDING INTO STOVE. IF YOU CANNOT SHUT OFF THE GAS LINE FEEDING INTO STOVE CONTACT A REPAIR MAN!!!!!!

Open bottom broiler drawer. Remove trays. Remove broiler drawer. Remove bolts holding heat sheild from back o ... Read more f oven (mine only had 2 bolt/screws holding 2 heat shields covering safty valve). Remove Heat shield. Unscrew 3/8" gas line feeding into safty valve on right. Remove 3 bolt/screws hold safety valve on back of oven. Remove Safty valve from oven. Unscrew Mounting Nut from old valve and place on new valve. Remount the new safty valve. Re-attach 3/8" gas line feeding into saftly valve. Replace heat sheild. Replace broiler drawer. Replace racks on broiler drawer. close Stove. Turn gas back on. Make sure you dont smell gas (I would wait at least 15 minutes before turning stove on to make sure there is no gas leak).

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

After receiving the part ordered in one day, I removed the racks and the bottom flame spreader. The igniter assy. is held in by two screws, which only took a minute to remove. I removed the ceramic wire ties from, the old igniter and wire tied in the new one. Put everything back together and tested the oven. It works great again. Thanks f ... Read more or the quick response and delivery.

The toughest part of the repair was the preparation to remove the old burners. As a result of the burning there was a carbon residue on the burners, on the gas outlet feed to the burners. This took some scrubbing and removing the carbon residue. Bits had burned onto the outlet and had to be scrapped off. Once all cleaned, replacing th ... Read more e burners was easy just had to place the balancing nuts in place and put on the burners. One problem arose the hood of the stove did not go back in place after replacing the burners so I then removed the balancing nuts put back on the burners stove top hood fit back in place and burners operated properly. This part of the repair took five minutes.

I removed all the burner heads with a torx driver & released the top of the stove by pushing in two clips with a screwdriver. I raised the top and located the thermostat as it fed through back of stove, then tied a line to the old thermostat to be used to pull the new one through. This did not work, so I removed a cover on the back of s ... Read more tove to provide more room & spread insulation apart so i could see hole. I was able to easily feed new thermostat through hole and reassemble.

First I removed the pan drawer. Then I removed the metal cover under the stove. Not sure if you have to remove that or not. I think I could have left that on. I then looked inside the oven and removed the two screws in the back to remove the lower cover. Ahh, the hot surface ignitor and flame grill exposed. I then turned on the oven again ... Read more to make sure the hot surface ignitor was not glowing. I went back underneath, and disconnected the hot surface ignitor. I followed the wires from it to where it was connected. I then unscrewed the 2 screws that held the flame grill in place. Next, I went back in the oven and removed the flame grill with the hot surface ignitor still attached. I then unscrewed the hot surface ignitor and replace it with the new one. Key points: make sure you mark which wire had which connector, or only cut one at a time. Also, they do not come with new clips, so don't cut you wire too short. I then fed the wires and the base of the flame grill back down the slot, rescrewed the flame grill to the oven, attached the wires, and turned on the oven to make sure it worked. I finally replaced the lower plate inside the oven, the lower plate under the oven, put the drawer back in and I was done.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.