362726 Kenmore Range - Instructions

I could not get these grates clean, so I called Partselect and they helped me find the model of the same stove that had black grates, drip pans, and burner caps. I ordered the black grates one afternoon, and without paying for expedited shipping, they arrived the next day! They were in original GE boxes (since they make Hotpoint). I am ... Read more happy about the whole experience.

First of all disconnect the power cord and then remove the top section of the oven which consisted of 2 small allen screws located in the front bottom corners [ left and right ] on the frontside. On the backside there was 2 phillip screws on top corners [ left and right ]. Also there was 2 bolthead screws that I use my small socket set or ... Read more you can use a small ajustable wrench. Once all these were removed it rolled forward right off. The control board was located in the center of the panel. Made sure the part matched up and it did, removed 4 small corner phillip screws and 4 or 5 removable plug in wire connectors which were easily identified. Put everything back together, plug power cord back in and the electronic display came on. Everything worked on the oven. done deal.

Removing all the shattered glass was endless it seemed. hovever the repair was very easy. Even for a very busy stay at home mom with limited handy man skills.I did it and it only took about 15 to 20 mins. once i got all the glass out of the way.I untightened the 4 sm.bolts under the door just enough to fit the glass in and when in place r ... Read more etightened the bolts and done !!

remove two screw lift top slide glass in place install top done deal

First I needed the correct model number & the correct part numbers for the two front tube assemblies. After that well.... I removed everything on top of the stove. I then proceded to remove all the torx screws for each orifice holder bracket & igniter wires so i could raise the top lid ( without this step you will wind up replacing more t ... Read more han one tube assembly!) Be careful when removing color coded wires so that they work with the correct burner. Remove compression nut to burner valve... i used a crowfoot. remove orifice holder from bracket & install new holder ( onto bracket). Install orifice assembly to burner valve ( do not over tighten), re-install wires to igniters, lower lid, and re-install torx screws. The correct parts require little effort to align. Last of all, test burners and check for leaks. Thanks for reading, I will continue to learn from my mistakes!

Really self explanatory. Removed the old drip pans and put in the new. No tools required. However, I would like to say I received the parts the day after I ordered them. EXTREMELY FAST SHIPPING!!

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

While i was inserting the new lp,gas orriface to the right rear burner tube I dropped the oriface.Without looking i popped the top of the burner unit, like most older type stoves, and thats when i ran into my problem. I realized the burner tube assemblies are attached by 3 screws to the top cover.Not attached to the cabinet as the older m ... Read more odels, Basically cracked both front aluminum tubes trying to retrieve the dropped oriface. so i had to replace the burner tube units, which involved removing 3 screws, and loosing up and removal of the nut to the main gas tube. extremely easy repair, next time i`ll try to remember look before i leap,total time to (r+r)burner tubes about 20 minutes.Parts select pulled me out of the fire on this one, great staff and service, with quick delivery.

Here's how I fixed my problem.
I took the aluminum cover, the part that sits over the jet & the igniter, which simply comes off. It's the part that the igniter discharges to. I took this cover off & using a pencil I scratched the lead of the pencil into the area
which is around the igniter. I made sure to cover the area wit ... Read more h as much lead as I could get on it. You need to make sure that you do this to all four burners. The only care you need to take, is not to block the gas jet which is in the igniter recess. It's been about 3 weeks since I added this & the burners click loudly & have lit without a problem. It appears that the aluminum may develop a coating on it of some kind which is highly resistive.

Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching ... Read more the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

On each side of the door at the top you will find an allen screw, remove those to remove the handle assembly. On the inside of the door, you will find two more silver allen screws, these release the glass frame. On the flimsy part that seperates from the main door frame, there are two small brackets that hold the glass panel. Remove those ... Read more using a #2 philips head screwdriver, then using a flat head screwdriver, carefully pry out all the ramaining glass shards. The glass frame will be very wobbly, this is a good time to have a friend around. place the new glass panel in the bottom slot first, then just hold it up, with a helper on one side, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame, and reinstall the handle. Now you have a nice new door front!

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.