362724 Kenmore Range - Instructions

Really self explanatory. Removed the old drip pans and put in the new. No tools required. However, I would like to say I received the parts the day after I ordered them. EXTREMELY FAST SHIPPING!!

1. Pull the oven out to access the connector in the back of the oven near the bottom center to disconnect the connector to the ignitor. Then push the connector and wire through the hole in the back of the oven.
2. Removed the broiler drawer to access the ignitor.
3. Removed the two screws holding ignitor to the burner bar, then ... Read more pull wire the remaining way through the rear hole.
4. Installed the new part with the two screws to the burner bar.
5. Insert the wires with connector througth the hole in the rear of the oven to reconnect to the plug at the back outside of the oven Reconnect the connector at the back of the oven.
6. Push the oven back in place and it is ready to use.

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

My Hotpoint gas oven became extremely hot after using it . Only after unplugging the electrical cord, turned it off. Replacing the control valve (thermostat) solved the problem. The stove top had to be pried up with a flat screw driver then propped up. Prying off the oven control valve revealed two mounting screws (philips ... Read more head). Next remove thermostat sensor bulb inside oven at back wall. Remove old thermostat control and bulb assembly. Installation is reverse order of disassembly.

removed two screws with screw driver,and replaced panel

1. Moved oven from the wall.
2. Unplugged the stove from the electrical outlet.
3. Removed over racks and bottom panel.
4. Located wires leading from the igniter in the back of the stove.
5. Disconnected the wires from the ignitor.
6. Used socket set to remove screws from ignitor.
7. Cut connector plug f ... Read more rom new ignitor.
8. Stripped about a half inch of insulation from wires of new ignitor to be able to connect it to stove.
9. Carefully handled new ignitor and screwed it into place.
10. Attached wires of new ignitor using new caps.
11. Put bottom panel and racks into place.
12. Plugged oven into electrical outlet - Oven ignited and made a good dinner.

Glass was a little messy cleaning up but removal and placement of new glass and side rails went easy.

I loosened the three gas line fittings on the valve, removed the two screws holding it to the frame, and removed the four wires (spade connectors). Then I reversed the process to install the new valve. It was that easy. This was my last resort after replacing the temperature probe and the control unit. It fixed the problem.

While i was inserting the new lp,gas orriface to the right rear burner tube I dropped the oriface.Without looking i popped the top of the burner unit, like most older type stoves, and thats when i ran into my problem. I realized the burner tube assemblies are attached by 3 screws to the top cover.Not attached to the cabinet as the older m ... Read more odels, Basically cracked both front aluminum tubes trying to retrieve the dropped oriface. so i had to replace the burner tube units, which involved removing 3 screws, and loosing up and removal of the nut to the main gas tube. extremely easy repair, next time i`ll try to remember look before i leap,total time to (r+r)burner tubes about 20 minutes.Parts select pulled me out of the fire on this one, great staff and service, with quick delivery.

This repair was fairly simple, just took the door off, then the 2 screws in the back, lift the bottom out. then remove shield to valve unplug the old igniter. then put it all back in reverse order. it worked great.

The R&R of the defective thermostat was at first look relatively simple. The job was made more complicated because in order to remove the old thermostat and then route the new thermostat across the top of the stove, under the burners, and down through a small hole into the oven space I had to remove the whole top of the stove. This proce ... Read more ss is not hard, just time consuming. Be very careful of razor sharp edges, they make you bleed. The final calibration of the oven is an easy adjustment in the oven knob. All in all it was an good experience.



Lyle Nelson

Here's how I fixed my problem.
I took the aluminum cover, the part that sits over the jet & the igniter, which simply comes off. It's the part that the igniter discharges to. I took this cover off & using a pencil I scratched the lead of the pencil into the area
which is around the igniter. I made sure to cover the area wit ... Read more h as much lead as I could get on it. You need to make sure that you do this to all four burners. The only care you need to take, is not to block the gas jet which is in the igniter recess. It's been about 3 weeks since I added this & the burners click loudly & have lit without a problem. It appears that the aluminum may develop a coating on it of some kind which is highly resistive.

Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching ... Read more the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.