3620PARTS Makita Router - Parts

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a high quality item that is specially manufactured for use with Makita power tools. It is a standard hardware which has multiple used depending on the tool, please make sure to check appropriate diagrams for correct use and application of this screw. One durable metal pan head screw is included per order.

The switch fits between the field assembly and the housing set. This part is available individually and is made out of plastic. When replacing this part a screwdriver and a set of pliers might be required during the installation process. It will need to be replaced if it becomes broken. This is a genuine replacement part sourced from the original manufacturer for use with Makita routers.

This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and planers. The flat washer is used with different types of power tools and the application of the washer can vary based on the model of the equipment. This item is available as an individual replacement part.

This is an OEM approved replacement Collet Nut that fits a various number of Makita router tools. The nut is used to form a collar around the tool, which when tightened works as a clamp. Made of durable high quality metal, the collet nut attaches the collet (sold separately) to the armature.

Genuine Makita replacement part, This item is sold individually. This screw is used mostly on the bases of the tool listed below. On the jig saws it is used to attach the Base Plate to the base. On the Router it is used to attach the Base Plate to the base On the Circular Saw it is used to attach the Depth Guide to the Base of the saw.

This replacement part is an original Makita item designed for use with a variety of power tools. This wing bolt has multiple uses based on a tool. For proper application please check units diagrams. It is a metal wing bolt and it is sold individually. No tools needed to secure or loosen it.

This item is available as an individual replacement part. The hex nut is made out of metal. A wrench might be helpful during the installation of this part. It might break or strip over time and will need replacing. This genuine item is supplied by the original equipment manufacturer for use with blowers, drills, grinders, nailers, rotary hammers, routers, sanders, saws, and trimmers made by Makita.

It is an authentic item which is supplied by the original equipment manufacturer for use with Makita power tools. The purpose of this flat washer is to provide a tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality metal and is sold individually.