3609 Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ice maker was leaking
2 of 2 people
found this instruction helpful.
-
Jay from Richardson, TX
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the h
... Read more
arness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker
I am not a good handyman but was able to install the new ice maker
Read less
Was this helpful?
Thank you for voting!
I went by the video but my removal and installation were different than shown.
2 of 2 people
found this instruction helpful.
-
Gregory from GARNER, KY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be rem
... Read more
oved and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.
Read less
Was this helpful?
Thank you for voting!
water leaking into ice tray, frozen glob of ice
2 of 2 people
found this instruction helpful.
-
james from newfield, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.
Was this helpful?
Thank you for voting!
Icemaker made some pretty sad cubes! Hollow, unfilled, or small cubes
2 of 2 people
found this instruction helpful.
-
Dana from ABINGTON, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.
Was this helpful?
Thank you for voting!
Not Cooling or freezing
2 of 2 people
found this instruction helpful.
-
Walton from Rainbow City, AL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Most difficult part was finding where they hid the defrost timer. (it is in the left front under the fridge behind the kick panel.) just unscrew the two fastener screws from the front, tilt fridge up on one side, slide timer bracket back and remove. Unplug and remove timer from metal bracket. Replace timer and remount bracket.
Was this helpful?
Thank you for voting!
Water started drip from freezer door.
4 of 8 people
found this instruction helpful.
-
Anders from Eagan, MN
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
Freezer full, so first thought door had been left slightly adjar. Verified the compressor was runing. Left to hopefully cool down. Did not happen. Searching for cause after covers were removed identified that fan in freezer was not working and ice had built up . While troubleshooting, the freezer went through a defrost cycle. Juryrigged t
... Read more
he fan to run continuosly and concluded the defrost thermostat must be the problem.
Installed new thermostate when recieved. No change! Deeper search then found crack in the defroster coil, which must have worked off and on but finaly failed completely.
Bought new refidgerator, as this was just one more problem with this older refridgirator. Also ordered new defroster coil to hopefully fix up the old refridgerator as a garage spare.
Installed new thermostate when recieved. No change! Deeper search then found crack in the defroster coil, which must have worked off and on but finaly failed completely.
Bought new refidgerator, as this was just one more problem with this older refridgirator. Also ordered new defroster coil to hopefully fix up the old refridgerator as a garage spare.
Read less
Was this helpful?
Thank you for voting!
Ice tray filled up with water. Stopped making ice.
2 of 2 people
found this instruction helpful.
-
robert from COLDSPRING, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people
found this instruction helpful.
-
Lyle from Bismarck, ND
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I removed the screws on the back of the refrigerator revealing the water valve, disconnected the water supply, removed the two outlet hoses and removed the bad valve. Replaced in the opposite manner.
Was this helpful?
Thank you for voting!
water overflow,coating on tray peeling off
2 of 2 people
found this instruction helpful.
-
Jeffery from vero beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will
... Read more
fall..all done.
Read less
Was this helpful?
Thank you for voting!
Bottom Cam broke on Fridge Door
2 of 2 people
found this instruction helpful.
-
Jon from Butler, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Socket set
Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.
Was this helpful?
Thank you for voting!
None
2 of 2 people
found this instruction helpful.
-
Dennis from Strongsville, OH
- Really Easy
- Less than 15 mins
My wife just snapped it in.
Was this helpful?
Thank you for voting!
One side of the kick plate grill was broken (faling of fridge).
2 of 2 people
found this instruction helpful.
-
Meghan from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped off the grill via the one remaining clip. Used a flathead screwdriver to pop the old, broken clip off. Then popped the new clip on to the holder. Done!! Super easy. Wish I had done it 2 years ago when the thing first broke instead of trying to jury-rig it!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
door closure part broken. door wouldn't remained closed
2 of 2 people
found this instruction helpful.
-
Patricia from JACKSON, WY
- Really Easy
- Less than 15 mins
-
Socket set
removed door.examined problem,. installed part. super easy
Was this helpful?
Thank you for voting!
Cracked bin (pan-fruit) - needed to be replaced.
2 of 2 people
found this instruction helpful.
-
Daniel from Columbia, SC
- Really Easy
- Less than 15 mins
How hard can replacing a bin be? Take out the old one and put in the new one. Time for actual repair: 1 minute.
Was this helpful?
Thank you for voting!