3605 - Instructions

Pulled out the fridge fro the wall, unpluged it, turned off the water supply to the house, disconnected the water line to the part, installed new part and re-attached the wires and ground, turned on the water - no leaks, plugged in the fridge - ice maker begand to fill and has continued to work.

Easy as pie. Will contact you a ... Read more gain if I have other appliance problems.

Paul M, Seattle WA

Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but t ... Read more he part was here in less than 2 days. Pretty awesome little company.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to ... Read more reach 10 degrees F to operate.

Very easy to order from parts select. Took seconds to replace.

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Emptied the door.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!

The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.

replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull en ... Read more d) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t ... Read more he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Wow! less Than 15 mins to install, called partSelect and within two days the Auger arrived and with handy socket it was done!

Have to say it was a pleasure doing business with PartSelect. Purchased the icebin from Whirlpool and the entire backside of the bin broke off in less than 10 days. I called Whirlpool for warranty and they said it had been more than 30 days since the order was placed and it is only a 30 day warranty. I spoke to a supervisor and pleaded my ... Read more case that I work out of town and only make it home every 2-3 weeks and it was only installed for 10 days. I further explained that the original unit lasted 10 years so I would think it would be pretty obvious that this was a defective product. She said sorry, only 30 day warranty, but she would offer a 25% discount if I wanted to reorder. I told her what I thought of their policy and offer and told her I would rather pay full price than any further support of their company.
The phone agent with PartSelect was friendly, professional and I received my new icebin in just a few days. I don't purchase many parts from the internet but I would bookmark this company for future reference.

Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring ... Read more harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away