EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

35HY Magic Chef Range - Instructions

All Instructions for the 35HY
31 - 45 of 132

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace clock-adjust knob
2 of 3 people found this instruction helpful.
  • OSCAR from BRISTOL, CT
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people found this instruction helpful.
  • Phillip from Reston, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
Used part
2 of 3 people found this instruction helpful.
  • Sabrina from FREMONT, CA
  • Very Easy
  • Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
burner would not heat.
1 person found this instruction helpful.
  • Jackie from Hughes Springs, TX
  • Really Easy
  • Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
Couldn't find correct drip bowls that fit.
2 of 4 people found this instruction helpful.
  • Lowell from Hardin, KY
  • Really Easy
  • Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people found this instruction helpful.
  • kathryn from piqua, OH
  • Really Easy
  • Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person found this instruction helpful.
  • Michael from Thornton, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this helpful?
Thank you for voting!
Burnt out
2 of 4 people found this instruction helpful.
  • David from Elba, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this helpful?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
1 person found this instruction helpful.
  • RICHARD from SHOW LOW, AZ
  • Very Easy
  • Less than 15 mins
Stuck the new one into the plugin.
Was this helpful?
Thank you for voting!
replace element
1 person found this instruction helpful.
  • alex from huntington, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person found this instruction helpful.
  • Helen from SPRINGFIELD, OH
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person found this instruction helpful.
  • Paul from SEATTLE, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Was this helpful?
Thank you for voting!
Infinite switch replacement.
1 person found this instruction helpful.
  • William from Kerens, TX
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I rep laced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person found this instruction helpful.
  • Sandra Collignon from SANTA CLAUS, IN
  • Really Easy
  • 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
All Instructions for the 35HY
31 - 45 of 132