EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

35HN Magic Chef Range - Instructions

All Instructions for the 35HN
16 - 30 of 136

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people found this instruction helpful.
  • Paul from Foley, AL
  • Really Easy
  • Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people found this instruction helpful.
  • Sharon from Yacolt, WA
  • Really Easy
  • Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people found this instruction helpful.
  • Barbara a from Huntington, NY
  • Really Easy
  • Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people found this instruction helpful.
  • Rachael from Adams, MA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this helpful?
Thank you for voting!
Replacement of broil element in wall oven
4 of 4 people found this instruction helpful.
  • David from San Rafael, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw d river is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Was this helpful?
Thank you for voting!
burner would not work
4 of 5 people found this instruction helpful.
  • David from Bellefonte, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people found this instruction helpful.
  • Terry from Mountain City, TN
  • Really Easy
  • Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people found this instruction helpful.
  • Paula Collins from Needham, MA
  • Really Easy
  • Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people found this instruction helpful.
  • Gary from Shirley, IN
  • Really Easy
  • Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
A switch on a front burner went out
5 of 10 people found this instruction helpful.
  • thomas from South Bend, WA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I first removed the back panel that covers the switches from back of stove; then I removed the wires and put them on the same numbered wires on the new switch; put the new switch in place with the wires connected to it; installed the 2 front screws and put the back cover on again & it took about 10 min and saved about $300.
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people found this instruction helpful.
  • George from Irving, TX
  • Really Easy
  • Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people found this instruction helpful.
  • Frances from Summerfield, FL
  • Really Easy
  • Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people found this instruction helpful.
  • Lynn from BRADENTON, FL
  • Really Easy
  • Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
All Instructions for the 35HN
16 - 30 of 136