35HB Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The original bake element burned out
-
William from Florissant, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The eleme
... Read more
nt did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.
Read less
Was this helpful?
Thank you for voting!
Drip bowls tarnished.
-
Jennifer from Albion, NE
- Really Easy
- 15 - 30 mins
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".
Was this helpful?
Thank you for voting!
Burner was always in high temperature.
-
Dennis from Oak Lawn, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.
Was this helpful?
Thank you for voting!
I had a power serge and it burned the Plug at the termial block and melted a few wire.
-
Robin from Vanderbilt, PA
- Really Easy
- 15 - 30 mins
-
Socket set
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this helpful?
Thank you for voting!
Burner stayed on "high", could not adjust heat
-
Deborah from Hodgen, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the bac
... Read more
k. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!
Read less
Was this helpful?
Thank you for voting!
Burner was in full hot.
-
Dennis from Oak Lawn, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number
... Read more
switches.
Read less
Was this helpful?
Thank you for voting!
Broil element burned out
-
Wallace from Lowell,, AR
- Easy
- 15 - 30 mins
-
Screw drivers
Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with nor
... Read more
mal tools.Thanks
Read less
Was this helpful?
Thank you for voting!
Burner did not heat, but element is ok.
-
Philip from Hull, MA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wi
... Read more
re lugs fit just fine, and the knob snapped right on and works great. Thank You!
Read less
Was this helpful?
Thank you for voting!
Right-side oven door spring broken
-
Ted from Horseshoe Bend, AR
- Easy
- 30 - 60 mins
-
Screw drivers
Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the c
... Read more
ooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!
Read less
Was this helpful?
Thank you for voting!
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
-
Ann from Schertz, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c
... Read more
an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Read less
Was this helpful?
Thank you for voting!
Easy installation
-
Jeremie from Freeland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push
... Read more
wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!
Read less
Was this helpful?
Thank you for voting!
The surface burner element burned out on my 20 year old Jenn Air electric stove.
-
Wanda from Riverton, WY
- Really Easy
- Less than 15 mins
It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major
Was this helpful?
Thank you for voting!
Burners quit working
-
Brenda from Brazoria, TX
- Really Easy
- Less than 15 mins
Bought two new replacement burners,they work great!
Other Parts Used:
Was this helpful?
Thank you for voting!
replacement of heating element for elec. stove
-
Erica from Ivyland borough, PA
- Really Easy
- Less than 15 mins
plugged it in to the spot where missing element was.
Was this helpful?
Thank you for voting!
The drip pans needed replacing.
-
Alison from Carnation, WA
- Really Easy
- Less than 15 mins
Put in the new drip pan -- which are really nice shiny ones.
Other Parts Used:
Was this helpful?
Thank you for voting!