This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.
This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on
Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.
The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.
This part is the replacement fuel cap assembly for your chainsaw. It is made of black plastic and is sold individually. The fuel cap prevents fuel from spilling out of the chainsaw and prevents debris from entering the fuel tank. If the fuel cap is stripped or missing the O-ring, it can cause a leak, and will need to be replaced. To repla...Read morece the fuel cap simply screw the old one out and screw the new one in, ensuring you have a tight seal. This is an authentic OEM part sourced directly from the manufacturer.
Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is made of metal.
If the pull cord will not retract into the housing, inspect the Recoil Spring for signs of wear or damage, replacing if ne...Read morecessary. You will need a screwdriver to complete this repair.
Customers rate this repair as Easy.
This is an authentic replacement carburetor which is supplied by the original equipment manufacturer for use with Craftsman chainsaws. The purpose of this part is to mix the air and the gas before the combustible mix goes into the engine, if the engine wont start and the tank is full of fresh fuel or if the engine starts and then quickly ...Read moredies, the carburetor is likely the problem. Please note this high-quality metal body component is sold individually, it includes the primer bulb.
Zama W-26
This Chain Bar Adjuster kit is a kit which contains all necessary hardware for adjusting a chain bar on a chain saw. Installation is rated as "Easy" and requires a screwdriver, wrench set and socket set. This part comes directly from the manufacturer.
The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.
It is a genuine OEM item that is made for Craftsman chainsaws. This is a special component which helps to provide a tight fit between connected parts. Over time it may wear out, get damaged or lost eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure the proper repair procedure. It consists of three durable metal parts.
Genuine Poulan replacement part, this item is sold individually. The purpose of the Air Filter is to block dust and debris from entering the carburetor and engine and causing damage. Once an Air filter becomes dirty, it constricts the flow of air to the engine making it not run properly. It is advised to keep an extra one or two on hand.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not start , had been sitting for years,
11 of 13 peoplefound this instruction helpful.
Sherri from BREAUX BRIDGE, LA
Easy
30 - 60 mins
Nutdriver, Screw drivers
I did not write detail steps , basically remove old carb replaced with new one, reassembled started right up no adjustments were needed !
Was this helpful?
Thank you for voting!
Worn out oil pump/burning chains
6 of 6 peoplefound this instruction helpful.
William from EVANSVILLE, IN
Really Easy
30 - 60 mins
Screw drivers, Socket set
After checking several different videos, ordered the repair parts and two specialty tools( Clutch removal/install and a worm drive remover/installer) Total for parts and tools around 45.00. Much cheaper than the shop wanted, 85.00 to look at it plus parts. As for results I've used the chainsaw all afternoon no problem. Runs like it did 12
... Read more yrs ago. Pumps oil the would make Jed Clampet proud
My neighbor brought the saw to me. It was locked up
4 of 4 peoplefound this instruction helpful.
Marvin from KIRBYVILLE, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers, Wrench (Adjustable)
He didn't want to spend alot of money on it. So I got the jug (Head) off and sanded it and the piston down while I waited on the new piston ring to get here. I found that it was easier putting the new ring in and the piston back into the jug (Head) was to go ahead and take the piston out so you could turn the jug (Head) upside down and it
... Read more slid right in. It didn't take no time at all. And it now runs as good as new