Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.
This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.
This is an authentic Husqvarna replacement screw that is commonly used on a variety of chainsaws, trimmers and brushcutters. It is a standard hardware which has multiple applications depending on your tool. Always make sure to check appropriate diagrams for correct location and use of this part. Please note, this screw has a hex socket head and it is sold individually.
This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.
It is a high-quality OEM item which is made for Husqvarna and Jonsered chainsaws. The piston is secured inside the cylinder in order to create pressure and push the oil. Over time due to friction and heat, it may wear out or even get damaged eventually requiring a replacement to maintain a properly working oil pump. Note, never use waste ...Read moreoil. This results in damage to the oil pump, the bar, and the chain. It is also important to use oil of the right grade (suitable viscosity range) in accordance with the air temperature. Make sure to refer to the owners manual and the appropriate diagrams of your model for the correct installation of the new part. You will need to use appropriate tools in order to remove the chain, the bar, and the sprocket in order to perform this repair. This pump piston is made of durable materials and is sold as an individual component. Keep in mind, other parts of the oiler mechanism are all sold separately.
This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.
This item has been sourced from the original manufacturer to ensure quality. The metal clutch drum is intended to be used with chainsaws from Husqvarna and Jonsered. This item is used to house the clutch and to drive the chain. The clutch expands when the saws engine increases RPMs and this rotates the clutch drum and the sprocket catches...Read more the chain to rotate it around the bar. This item is available as an individual replacement part.
This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.
This pinion is available as an individual replacement part. It fits between the needle bearing and the pump piston. The pinion is made out of metal and plastic and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part. This is an authentic replacement part for chainsaws made by Husqvarna and Jonsered.
This is a genuine OEM approved replacement screw made for Husqvarna chainsaws and brush cutters. It is a standard hardware which has multiple uses based on your equipment. Please refer to diagrams for correct application. It is made out of metal and it is sold individually. You would need a torx screwdriver to install or remove this screw.
This replacement hardware is an authentic OEM sourced item, it is not an aftermarket imitation. It is commonly utilized on Husqvarna and Poulan chainsaws. This screw has multiple applications depending on the equipment. Please make sure to check appropriate diagrams for correct location and use of this hardware. One hex socket head screw is included per order.
This is a genuine OEM part. The chain catcher pin is made for use with many chainsaw devices. The durable metal component is considered a safety feature, as it is designed to keep the chain from flying from the bar if it becomes damaged. The chain catcher pin is sold individually. A hex key and a wrench set may be necessary for the instal...Read morelation. Keep in mind, the bolt or screw is sold separately. Please refer to the specific manual for further repair instructions.