EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3553 - Instructions

All Instructions for the 3553
91 - 105 of 255

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken freezer door cam and leaking freezer door gasket
2 of 4 people found this instruction helpful.
  • Chris from Granite Falls, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
First I pulled the fridge out from the wall and turned off the water supply. Next I removed the access panel on the bottom front of the fridge. Located behind the panel was the water supply line for the water dispenser in the door which has a disconnect the I simply unscrewed so that I would be able to lift the door off of the bottom hi nge. Next I took one screw out of the top hinge cover to access three small bolts and disconnect the electrical connections to the door. After removing the bolts I lifted the door off and took out the small screw holding in the bottom cam and replaced with the new one. After reinstalling door I removed all the small bolts holding on the freezer gasket. After this the gasket easily pulls out and began installing the new gasket. This part of the job was the most time consuming. After I had the gasket back behind the pinch rail I began reinstalling the bolts. Since the gasket was bent during shipping I simply took a hair dryer to the slightly bent parts of the gasket to get them to lay flat. Freezer now has a great seal and stays closed when refrigerator door is being shut.
Was this helpful?
Thank you for voting!
Location of the run capacitor was not as the video described.
1 person found this instruction helpful.
  • Robert from Webbers Falls, OK
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigera tor is still too wide but it's colder.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people found this instruction helpful.
  • Carolee from Spokane Valley, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person found this instruction helpful.
  • Michael from Colorado Springs, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Freezer occasionally had a temperature alarm.Clicking noise also.
1 person found this instruction helpful.
  • Barry from FORD CITY, PA
  • Really Easy
  • Less than 15 mins
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this helpful?
Thank you for voting!
Plugged it in.
1 person found this instruction helpful.
  • Adam from GLOVERSVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
Compressor would not start and run, kept making a clicking noise.
1 person found this instruction helpful.
  • James from St.Johns, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unplugged the refrigerator, then removed the lower back panel to get access to the compressor. Then I removed the original compressor start relay, removing the metal clip and unplugged it from the side of the compressor. Installed the new compressor start relay from partselect. Plugged the appliance back in and the refrigerator st arted working again immediately with the compressor running properly and no more clicking sound. Reinstalled lower back panel.
Was this helpful?
Thank you for voting!
No cold
1 person found this instruction helpful.
  • Jacqueline from LEXINGTON PK, MD
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people found this instruction helpful.
  • Cathy from HOPATCONG, NJ
  • Very Easy
  • Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
compressor not running
1 person found this instruction helpful.
  • Doug from Lancaster, CA
  • Really Easy
  • 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
Worked like a charm. Thanks
1 person found this instruction helpful.
  • Keith from Cherryville, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires... Put a thermometer in a glass of water & now runs at 38 degrees.
Was this helpful?
Thank you for voting!
Fridge would warm above acceptable levels.
1 person found this instruction helpful.
  • Doug from BRANDON, MS
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Talked to a bud who does this kind of work and he walked me thru the simple job. Also watched a you tube segment. Very easy job. Took off the front kick vent panel. Unscrewed the metal holder and unplugged old part, plugged new part in and put panel back on. Turned on unit and it is working like a charm. Got my fingers crossed just in cas e.
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people found this instruction helpful.
  • Richard from North Easton, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people found this instruction helpful.
  • Douglas from Mesa, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
Motor noise while running and clicking when shutting off
1 of 2 people found this instruction helpful.
  • Curtis from Sedona, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this helpful?
Thank you for voting!
All Instructions for the 3553
91 - 105 of 255