3553 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Not Defrosting
6 of 8 people
found this instruction helpful.
-
Joe from Rockwall, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Disconnected power cord, Removed lower front face plate, removed one screw that helt cover over defrost timer, removed two screws that held timer, unpluged timer and removed it. Replaced old timer with new timer. Replaced timer installed two screws and replaced cover.
Was this helpful?
Thank you for voting!
Freezer gasket had tear
5 of 5 people
found this instruction helpful.
-
Roxanna from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Nutdriver
Loosened all retaining screws around gasket - removed old gasket - inserted new gasket and tightened screws. Little tedious (lots of screws) but very simple.
Was this helpful?
Thank you for voting!
refrigerator not cooling properly
6 of 9 people
found this instruction helpful.
-
Ernie from Windsor, CA
- Really Easy
- 1- 2 hours
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is
... Read more
now running as it should.
Read less
Was this helpful?
Thank you for voting!
Click
4 of 4 people
found this instruction helpful.
-
James from FLATWOODS, KY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
By following your information
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people
found this instruction helpful.
-
Dave from Manchester Center, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people
found this instruction helpful.
-
Joseph from Byron Center, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m
... Read more
e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Read less
Was this helpful?
Thank you for voting!
Broken wheel
4 of 5 people
found this instruction helpful.
-
Eric from Woods Cross, UT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.
Was this helpful?
Thank you for voting!
Cam snapped in half on bottom of door
3 of 3 people
found this instruction helpful.
-
Mason from Tallahassee, FL
- Easy
- Less than 15 mins
-
Screw drivers
Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but t
... Read more
he part was here in less than 2 days. Pretty awesome little company.
Read less
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!
door would not self close tightly
3 of 3 people
found this instruction helpful.
-
paula from julian, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove two screws from top door hinge.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.
Was this helpful?
Thank you for voting!
clicking sound
3 of 3 people
found this instruction helpful.
-
Ronald J from TULSA, OK
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unplugged the power and removed the cardboard back Unplugged the part and power from the side of the compressor Plugged the power and new part back in to the side of the compressor and replaced the clamp Plugged in the power cord to the wall outlet and the refrigerator started to hum Job done Thanks
Was this helpful?
Thank you for voting!
Refrig began to trip the GFI circuit in the garage. When plugged into a house interior circuit the lights and fan ran but no cooling in either the freezer or frig.
3 of 3 people
found this instruction helpful.
-
riley from CAVE CREEK, AZ
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Ref
... Read more
er to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!
Read less
Was this helpful?
Thank you for voting!
Door would not close properly
3 of 4 people
found this instruction helpful.
-
Sarkis from Havertown, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the door by taking 3 screws out of the top and lifting straight up, then replaced with the new parts and very easily replaced the door, worked ike a charm, if i didn't know any better it was like factory new
Was this helpful?
Thank you for voting!
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people
found this instruction helpful.
-
Tonya from Grand Prairie, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f
... Read more
an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Read less
Was this helpful?
Thank you for voting!