3542 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace the lower oven element
1 person
found this instruction helpful.
-
Tom from ROCKTON, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person
found this instruction helpful.
-
Bruce from SOUTHBURY, CT
- Really Easy
- 30 - 60 mins
-
Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
Oven baking coil had burned out
1 person
found this instruction helpful.
-
Marie from Fredericksburg, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.
Was this helpful?
Thank you for voting!
The bake element burst.
1 person
found this instruction helpful.
-
Diane from Littleton, CO
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this helpful?
Thank you for voting!
Wife said stove was on fire - Oven element shorted.
1 person
found this instruction helpful.
-
James from Hoyt Lakes, MN
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was
... Read more
fixing the oven element my wife replaced the oven light.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake element would no longer heat up
1 person
found this instruction helpful.
-
Joe from Schertz, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the
... Read more
holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Read less
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people
found this instruction helpful.
-
Tawnia from SHOW LOW, AZ
- Really Easy
- Less than 15 mins
take out the old put in the new
Other Parts Used:
Was this helpful?
Thank you for voting!
snapped element
1 person
found this instruction helpful.
-
Paul from Yukon, OK
- Easy
- Less than 15 mins
-
Screw drivers
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
recieved my replacement part the next day after ordering
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
Wayne from Marietta, GA
- Easy
- Less than 15 mins
-
Screw drivers
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this helpful?
Thank you for voting!
Bake Element Melted
1 person
found this instruction helpful.
-
Bert from S. Easton, MA
- Easy
- Less than 15 mins
-
Screw drivers
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in.
... Read more
Plugged stove in and worked perfect.
Read less
Was this helpful?
Thank you for voting!
Element burned out.
2 of 4 people
found this instruction helpful.
-
Raymond from Ottawa, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this helpful?
Thank you for voting!
element burnt into.
1 person
found this instruction helpful.
-
John from Overton, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The part came quick and packed very well. I moved the stove out and un pluged it. opened oven door and took a philips screwdriver and took the screws out at the back of element..Slid it out with the two wires attached and unpluged the conectors. pluged the conectors on to the new element and slid it back in. Had a chocolate cake in 35
... Read more
minuts.
Thanks, John in Texas
Thanks, John in Texas
Read less
Was this helpful?
Thank you for voting!
Bake Element broke
1 person
found this instruction helpful.
-
Joseph from Warwick, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into th
... Read more
e holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
Read less
Was this helpful?
Thank you for voting!
Our original surface element caught fire!
1 person
found this instruction helpful.
-
Paulo from Cambridge Springs, PA
- Really Easy
- Less than 15 mins
Old surface element was removed simply by pulling it out of the electrical contacts. The, the new one was inserted.
Was this helpful?
Thank you for voting!
hot spot in center of bake element appeared suggesting failure was imminent
1 person
found this instruction helpful.
-
burton from prides crossing, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.
Total time 10 minutes,even a caveman could do it.
Was this helpful?
Thank you for voting!