3523 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake Element shorted out
1 person
found this instruction helpful.
-
Laurie from Clarence, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I first shut off the breaker to the stove - safety first!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
Read less
Was this helpful?
Thank you for voting!
bottom bake element broken and burned
1 person
found this instruction helpful.
-
Carolyn S from white oak, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Was this helpful?
Thank you for voting!
Previous element burnt up
1 person
found this instruction helpful.
-
Betsy from Sun City, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.
Was this helpful?
Thank you for voting!
The bake element burst.
1 person
found this instruction helpful.
-
Diane from Littleton, CO
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this helpful?
Thank you for voting!
Wife said stove was on fire - Oven element shorted.
1 person
found this instruction helpful.
-
James from Hoyt Lakes, MN
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was
... Read more
fixing the oven element my wife replaced the oven light.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Replace the lower oven element
1 person
found this instruction helpful.
-
Tom from ROCKTON, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Was this helpful?
Thank you for voting!
selector switch not smooth and no heat on element
1 person
found this instruction helpful.
-
TUONG from ALBANY, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
un-plug device from outlet for safety first and then remover all top panel after screws lower two side small screws. actually is not selector problem. It was burner switch problem for 6 inches element.
Was this helpful?
Thank you for voting!
original fixture required bulb - this fixture (all-in-one) was great
1 person
found this instruction helpful.
-
wesley from ODENVILLE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
lens light was broken and missing.
1 person
found this instruction helpful.
-
Allan from Rolla, MO
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop <
... Read more
br />and turned electrical power on.
Read less
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
oven didn't heat up
1 person
found this instruction helpful.
-
robert from merrimack, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
Was this helpful?
Thank you for voting!
Lower element out-oven wouldn't heat
1 person
found this instruction helpful.
-
PATSY from HALLWOOD, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!
Was this helpful?
Thank you for voting!
bake element disintegrated!
1 person
found this instruction helpful.
-
Susan from Grand Ledge, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
Was this helpful?
Thank you for voting!
Bottom Element Burned out
1 person
found this instruction helpful.
-
Robert from Jacksonville, FL
- Easy
- 15 - 30 mins
-
Screw drivers
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Was this helpful?
Thank you for voting!
Lower burner not heating:
1 person
found this instruction helpful.
-
John from Fishers, IN
- Easy
- 15 - 30 mins
-
Screw drivers
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back
... Read more
cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600
Read less
Was this helpful?
Thank you for voting!