3520SPA Magic Chef Range - Instructions

removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.

Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

just move one wire at a time. Each switch has 5 wires and I am sure mixing them would not be good.

Ordered parts, they shipped same day. Arrived exactly as predicted. Totally non-stress. Can't find a thing to complain about.

Thanks PartSelect

Pulled the oven away from the wall. Removed two screws inside the oven. Pulled old heating element out. When I did I heard a loud pop and and saw smoke. I assumed the element would not be electrically live if the oven was not on. That was obviously incorrect. I pulled the plug and then completed the installation. I went to chruch o ... Read more n Sunday and thanked God that I was not electrocuted. Now the oven works fine. My wife wanted the oven to die so that she could get a new alppliance, Instead I am alive.

Seriously your service was great. Your web site pointed me to the correct part, and it arrived the next day! I would definitely use your service again if I remember your name.

As I pulled the drawer looking for a pan stored in bottom drawer the drawer glide broke. The pictures of the parts were fantastic. Not being sure of which of two parts from the photos, I ordered two parts knowing that hopefully one would be the correct one and the other would not be the part I needed. Parts arrived and it was clear whic ... Read more h of the two parts would fit perfectly.

I screwed in the part, and that was it , and I was relieved that the problem was solved! I kind of feel lucky that your company is in business! The other part is fully accepted and plan to send it back in for a refund. And oh yes, I solved my appliance problem under $20.00 - unbelieveable these days!

Thank you again for beng there!

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also ... Read more used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power ... Read more and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.