3512WPL Magic Chef Range - Instructions

First I removed the old bowls and replaced them with the new.

took old bowls out, put new bowls in, took a coffee break

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister ... Read more 's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Took out the old drip bowls and replaced with new bowls.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes proper ... Read more ly, the heat stays in the oven!!

Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. On ... Read more ce off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland