3510PPA Magic Chef Range - Instructions

Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

Pulled the oven away from the wall. Removed two screws inside the oven. Pulled old heating element out. When I did I heard a loud pop and and saw smoke. I assumed the element would not be electrically live if the oven was not on. That was obviously incorrect. I pulled the plug and then completed the installation. I went to chruch o ... Read more n Sunday and thanked God that I was not electrocuted. Now the oven works fine. My wife wanted the oven to die so that she could get a new alppliance, Instead I am alive.

Seriously your service was great. Your web site pointed me to the correct part, and it arrived the next day! I would definitely use your service again if I remember your name.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS

First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also ... Read more used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

I removed the two screws that held the element in. I pulled the old element out and heard a loud pop. I didn't realize that I had to turn the oven off at the breaker to change the element. It blew the breaker and melted one of the connectors to the element. The wires didnt pull through the hole so I had to pull the oven out, take the b ... Read more ack panel off, replace the electrical connectors, slide the wires through the holes at the back of the oven, connect the element and put it back in, now it works fine. Remember to turn the oven off at the breaker when changing the element, it could be a shocking experience otherwise.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

replaced drip pans with correct type

You guys had a installation video which help greatly. I did run into a couple issues. Firstly, it didn't see a plug for the oven so I shut the power down from the panel. Lastly, disconnecting the old bake element from the electric insert at the ends was a bit challenging. The element and the inserts looks as if it was one piece but event ... Read more ually it pulled apart. Installing the new piece was very easy. You want to consider adding additional legs under the bake element closet the area where the element connect to the oven inserts. When my old element broke and failed, the live piece can in contact with the floor of the oven causing a flash. It was a bit scary.

Thank you very much for your expeditious shipment and your follow up. Great job!

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only too ... Read more k about 5 minutes to fix, and I saved at least $100 by not having to call a service man.

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.