EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

34GY Magic Chef Range - Instructions

All Instructions for the 34GY
76 - 90 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven igniter although lit up it failed to permit gas valve to open
2 of 2 people found this instruction helpful.
  • Teresa from BRICK, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people found this instruction helpful.
  • Peter from Westcliffe, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people found this instruction helpful.
  • edward from euclid, OH
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people found this instruction helpful.
  • OSCAR from BRISTOL, CT
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people found this instruction helpful.
  • jeff from haskell, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug ged it into the harness in the back and reinstalled oven in the cabinet.
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people found this instruction helpful.
  • Robert from Clymer, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people found this instruction helpful.
  • Daniel from MOUNT HEALTHY, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people found this instruction helpful.
  • Barbara L. from Tewksbury, MA
  • Really Easy
  • Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
Range burner drip pans were rusted and old
3 of 6 people found this instruction helpful.
  • Billye from San Antonio, TX
  • Really Easy
  • 15 - 30 mins
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ture for needed parts.
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people found this instruction helpful.
  • Donald from Peebles, OH
  • Really Easy
  • Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
rusty drip trays
2 of 3 people found this instruction helpful.
  • Pam from Grand Ledge, MI
  • Really Easy
  • Less than 15 mins
finally after years of searching for trays of this size with no luck in local stores, I was able to find and purchase 2 sets, one set for my daughter, which we were able to put in place to clean up our stoves and make them more appealing . Thank-you for your prompt service.
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person found this instruction helpful.
  • Joe from West Winfield, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person found this instruction helpful.
  • RONNIE from SAG HARBOR, NY
  • Easy
  • Less than 15 mins
  • Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people found this instruction helpful.
  • Ben from Belen, NM
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person found this instruction helpful.
  • Michael from Syracuse, NY
  • Easy
  • 15 - 30 mins
  • Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Was this helpful?
Thank you for voting!
All Instructions for the 34GY
76 - 90 of 326