34GV Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven making whooshing sound and not heating up
1 of 2 people
found this instruction helpful.
-
Jason from Williamsburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
Was this helpful?
Thank you for voting!
smell gas and sometimes a whoof on ignition
1 of 2 people
found this instruction helpful.
-
Maynard from Knox, IN
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .
Was this helpful?
Thank you for voting!
Oven Ignitor went to ignitor heaven.
1 of 2 people
found this instruction helpful.
-
Brian from Pittsburgh, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I wou
... Read more
ld absolutely use your services again. Oven is back to working great! Thank you!
Read less
Was this helpful?
Thank you for voting!
my stovetop light did not work
1 of 2 people
found this instruction helpful.
-
Geraldine M. from Fork Union, VA
- Really Easy
- 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc
... Read more
e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
1 of 3 people
found this instruction helpful.
-
Anatoly from Palatine, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.
Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.
Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
Read less
Was this helpful?
Thank you for voting!
Error code F-1&F-3
1 of 3 people
found this instruction helpful.
-
Carl from Franklin, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove two screws back panel and remove sensor two screws inside top oven.
Was this helpful?
Thank you for voting!
oven would not heat up
1 of 3 people
found this instruction helpful.
-
Albert from Charlotte, TN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
it was so easy my wife could do it!!!!!!!!
Was this helpful?
Thank you for voting!
oven in range would not stay lit or achieve temperature
1 of 3 people
found this instruction helpful.
-
Raymond from Jersey City, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range
... Read more
, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.
Read less
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").
1 of 3 people
found this instruction helpful.
-
Linford from Cedarville, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ... Read more ignition was less than 15 seconds with over one inch flame from burner.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ... Read more ignition was less than 15 seconds with over one inch flame from burner.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not light.
0 of 1 people
found this instruction helpful.
-
Phillip from Prescott, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then ... Read more removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!
I then ... Read more removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!
Read less
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people
found this instruction helpful.
-
Alan from Cinnaminson, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven wor
... Read more
ks properly. Thanx!
Read less
Was this helpful?
Thank you for voting!
oven did not reach temperature and was slow to heat up
0 of 1 people
found this instruction helpful.
-
kevin from west pittston, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.
Was this helpful?
Thank you for voting!
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
0 of 1 people
found this instruction helpful.
-
ALISE from LUDLOW, MA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took ab
... Read more
out 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
Read less
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people
found this instruction helpful.
-
Ron from Belleville, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit
... Read more
er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Read less
Was this helpful?
Thank you for voting!