EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

34GG Magic Chef Range - Instructions

All Instructions for the 34GG
91 - 105 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not heat up fully, smelled of gas.
1 person found this instruction helpful.
  • Brian from Spotswood, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person found this instruction helpful.
  • FRANCES from AFFTON, MO
  • Very Easy
  • Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person found this instruction helpful.
  • Nola from Enid, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person found this instruction helpful.
  • Gino from ARLETA, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person found this instruction helpful.
  • Karen from DAYTON, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 person found this instruction helpful.
  • Larry from LAWTON, MI
  • Very Easy
  • Less than 15 mins
  • Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person found this instruction helpful.
  • Marvin from DECATUR, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person found this instruction helpful.
  • Jacob from LITTLE CANADA, MN
  • Really Easy
  • 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
1 person found this instruction helpful.
  • Ernest from CINCINNATI, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person found this instruction helpful.
  • june from wills point, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person found this instruction helpful.
  • ELMER from BONNEY LAKE, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
No heat in oven
1 person found this instruction helpful.
  • Cynthia from AURORA, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
gas oven would not light
1 person found this instruction helpful.
  • carmine from ABINGTON, PA
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person found this instruction helpful.
  • Glynne from Dedham, MA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person found this instruction helpful.
  • Matt from Arlington, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this helpful?
Thank you for voting!
All Instructions for the 34GG
91 - 105 of 326