34GA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven igniter although lit up it failed to permit gas valve to open
2 of 2 people
found this instruction helpful.
-
Teresa from BRICK, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.
Other Parts Used:
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
Continuous sparking on all burners due to broken ignition switch
2 of 2 people
found this instruction helpful.
-
Hannah from AMHERST, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
1. I accessed the burner ignition switches by lifting off stove top, sliding off burner knobs and oven knob, and removing the front switch cover (secured with 4 screws on top and 2 screws underneath).
2. I diagnosed which switch was broken: all four switches are wired together, so one faulty switch will affect sparking on both ... Read more the left and right sides of the stove. I suspected a particular switch because that burner had occasionally struggled to ignite in recent weeks and felt "loose" when turned on.
After unplugging the stove from the electrical outlet and turning on the range fan, I slid several of the switches off their gas valve stems. When comparing the suspect switch to two other switches, the suspect switch felt "loose" when rotated and didn't have the same places of resistance that the other two had.
Feeling more confident that I had found the broken switch, I used pliers to pull out the four wires connecting the suspect switch to the other switches -- it took a good bit of force, there's no convenient release. Now I could access the switch terminals, so I used a multimeter to confirm that the suspect switch didn't have any change in electrical resistance when turned on/off -- it was broken.
3. I removed the broken switch and wired its neighbors together. I plugged the stove back in and checked that this had solved the problem -- no more continuous sparking, and the other three burners still worked.
While I waited several days for the replacement switch to arrive, I reassembled everything besides the broken burner's knob (to remind me to not use that burner), and continued using the other three burners normally.
4. When the replacement switch arrived, I inserted the original four wires into the new switch's terminal holes in the original configuration (again, it took a little force), reassembled everything, and was good to go.
2. I diagnosed which switch was broken: all four switches are wired together, so one faulty switch will affect sparking on both ... Read more the left and right sides of the stove. I suspected a particular switch because that burner had occasionally struggled to ignite in recent weeks and felt "loose" when turned on.
After unplugging the stove from the electrical outlet and turning on the range fan, I slid several of the switches off their gas valve stems. When comparing the suspect switch to two other switches, the suspect switch felt "loose" when rotated and didn't have the same places of resistance that the other two had.
Feeling more confident that I had found the broken switch, I used pliers to pull out the four wires connecting the suspect switch to the other switches -- it took a good bit of force, there's no convenient release. Now I could access the switch terminals, so I used a multimeter to confirm that the suspect switch didn't have any change in electrical resistance when turned on/off -- it was broken.
3. I removed the broken switch and wired its neighbors together. I plugged the stove back in and checked that this had solved the problem -- no more continuous sparking, and the other three burners still worked.
While I waited several days for the replacement switch to arrive, I reassembled everything besides the broken burner's knob (to remind me to not use that burner), and continued using the other three burners normally.
4. When the replacement switch arrived, I inserted the original four wires into the new switch's terminal holes in the original configuration (again, it took a little force), reassembled everything, and was good to go.
Read less
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people
found this instruction helpful.
-
Peter from Westcliffe, CO
- Easy
- 30 - 60 mins
-
Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people
found this instruction helpful.
-
jeff from haskell, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug
... Read more
ged it into the harness in the back and reinstalled oven in the cabinet.
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Range burner drip pans were rusted and old
3 of 6 people
found this instruction helpful.
-
Billye from San Antonio, TX
- Really Easy
- 15 - 30 mins
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
Read less
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people
found this instruction helpful.
-
Daniel from MOUNT HEALTHY, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people
found this instruction helpful.
-
Barbara L. from Tewksbury, MA
- Really Easy
- Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
lamp retainer gasket disintegrated when changed burned out bulb
2 of 3 people
found this instruction helpful.
-
Sandra from Flemington, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people
found this instruction helpful.
-
Donald from Peebles, OH
- Really Easy
- Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
rusty drip trays
2 of 3 people
found this instruction helpful.
-
Pam from Grand Ledge, MI
- Really Easy
- Less than 15 mins
finally after years of searching for trays of this size with no luck in local stores, I was able to find and purchase 2 sets, one set for my daughter, which we were able to put in place to clean up our stoves and make them more appealing . Thank-you for your prompt service.
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!