34FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven would not light even though the glow plug lit.
0 of 1 people
found this instruction helpful.
-
HELMUT from MIDDLE VILLAGE, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people
found this instruction helpful.
-
Richard from Farmington Hills, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags.
... Read more
However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Read less
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people
found this instruction helpful.
-
mitch from brooklyn park, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people
found this instruction helpful.
-
Ron from Belleville, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit
... Read more
er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Read less
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people
found this instruction helpful.
-
MIKE from Phelan, CA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for
... Read more
years because I didn't realize how easy the fix was.
Read less
Was this helpful?
Thank you for voting!
The oven gas valve would not turn on
0 of 1 people
found this instruction helpful.
-
Steve from Prospect Heights, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Replaced the oven ignitor. Toughest part was removing old screws.
Was this helpful?
Thank you for voting!
Burners would not light sometimes
1 of 4 people
found this instruction helpful.
-
Robert from St. Remy, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
joan from florissant, MO
- Easy
- 15 - 30 mins
-
Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
Oven burner would night ignite
0 of 1 people
found this instruction helpful.
-
Douglas from Hanover Park, IL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was hard
... Read more
er than this.
Read less
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people
found this instruction helpful.
-
Anthony from Camillus, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
Oven Was Dead
0 of 1 people
found this instruction helpful.
-
IRIS from BROOKLYN, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is hel
... Read more
d on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.
Read less
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people
found this instruction helpful.
-
collins from Freeport, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
Oven would't heat
0 of 1 people
found this instruction helpful.
-
Sidney from Hindman, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I ... Read more have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I ... Read more have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
Read less
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people
found this instruction helpful.
-
Christopher from Dearborn, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people
found this instruction helpful.
-
Neville from Lithonia, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!