3458XVB Magic Chef Range - Instructions

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull ... Read more the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.

Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. ... Read more I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.

The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti ... Read more lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".

1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten

The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th ... Read more e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

I didn't. Don't know how to get to light bulb to change it for this specific model

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. ... Read more Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi ... Read more th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.