3428 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person
found this instruction helpful.
-
FRANCES from AFFTON, MO
- Very Easy
- Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
Oven gasket on door was very old. Oven door did not close properly.
1 person
found this instruction helpful.
-
Margaret from Clarendon Hills, IL
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed a simple video and completed this repair in just 5 minutes, gasket came out easily and the new one went in easily . Cleaning the oven door was the hardest part.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person
found this instruction helpful.
-
Jacob from LITTLE CANADA, MN
- Really Easy
- 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person
found this instruction helpful.
-
Matt from Arlington, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing
... Read more
the parts. Working in the oven was by FAR the most difficult part of the entire process.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat, broiler would.
2 of 4 people
found this instruction helpful.
-
Pati from Marietta, GA
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person
found this instruction helpful.
-
Glynne from Dedham, MA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
gas oven would not light
1 person
found this instruction helpful.
-
carmine from ABINGTON, PA
- Very Easy
- 30 - 60 mins
-
Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
1 person
found this instruction helpful.
-
Ernest from CINCINNATI, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person
found this instruction helpful.
-
Tara from ALBANY, NY
- Easy
- 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people
found this instruction helpful.
-
eric from winter haven, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
No heat in oven
1 person
found this instruction helpful.
-
Cynthia from AURORA, MN
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
Burners would not lite
2 of 4 people
found this instruction helpful.
-
Lloyd from Cocoa, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person
found this instruction helpful.
-
ELMER from BONNEY LAKE, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person
found this instruction helpful.
-
Michael from Syracuse, NY
- Easy
- 15 - 30 mins
-
Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an
... Read more
d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Read less
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person
found this instruction helpful.
-
june from wills point, TX
- Easy
- 15 - 30 mins
-
Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!