326C (2002-08) Husqvarna Brush Cutter - Parts

Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.

This OEM fuel line, or hose, is a 4-inch, clear, plastic tube which is sold individually. It is rated as "Easy" to install. This part connects to the purge assembly and delivers fuel to the carburetor or is used as a return line to the tank. A broken hose will leak, and should be replaced. Refer to your make, model and diagrams to check if this part is right for you.

The air cleaner knob, just over 1 inch in diameter, is black in color and made of plastic. It is sold individually, and its function is to tighten the air cleaner cover down on various lawn and garden equipment. This knob can become worn over time, which will cause the air filter cover not to stay in place. Most of our customers find this to be an easy repair. It does not require any special tools.

This replacement screw is an authentic Husqvarna part. It is a genuine manufacturer approved part commonly used on a variety of power equipment including chainsaws, trimmers and sweepers. This standard hardware is utilized in many different placed depending on a tool. Please make sure to check appropriate diagrams to verify correct locati...Read moreon and application for this screw. It has hex head that will require a wrench to install or remove it and it is sold individually.

This air filter comes in black foam and is rated as "Easy" to install. Installation requires a screwdriver, and the part attaches inside of the air cleaner housing. This manufacturer certified filter is used to prevent dirt and debris from entering the carburetor and engine, which would cause damage. If broken or clogged, the engine will ...Read moreexperience performane issues or may not turn on. If broken, the filter should be replaced. Tip: Put a bit of two-cycle oil in the bag and let it absorb into the filter. This makes it more tacky to catch debris.

The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.

This OEM carburetor mixes the air-fuel mixture to the proper ratio for combustion in your engine. This carburetor is sold individually, is silver in color and metal in material, and is located on the intake of the engine. Issues with your carburetor will cause problems with your engine running, and could cause excessive smoke due to too...Read more much gas. This can happen due to corrosion inside the carburetor. Carburetors can be rebuilt easily, and repairing them requires an allen wrench and a screwdriver. When troubleshooting your carb, remove the air filter and pour a teaspoon of fuel into the carburetor. Pull the starter rope, and if the engine starts then quickly dies, the carburetor is likely the problem. When replacing your carburetor, also replace all gaskets when doing so, as they are a one-time use.

This fuel tank bushing grommet creates a tight seal where the fuel line enters the tank, helping prevent leaks and keep air and debris out of the fuel system. Made from durable, fuel-resistant rubber, it supports reliable engine performance and consistent fuel flow. Replacing a worn or damaged grommet can help eliminate leaks and restore proper operation.

This is an authentic OEM sourced replacement screw designed for use with a variety of Husqvarna power equipment. It is a standard hardware which has multiple applications based on your tool. This part is made out of Metal and it is Sold Individually. Requires a Hex Key or a Wrench to tighten/loosen this Screw.

This is a genuine OEM part. The Husqvarna choke control is made for use with many lawn and garden trimmers. The plastic component is fastened to the carburetor, allowing the operator to manage the engine's fuel and air mixture. A hex key and a wrench may be required for making the repair. The choke control is sold individually.

This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. T...Read morehe O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.

This Carburetor Gasket provides a tight seal between the carburetor and insulator. If broken, the engine will run lean due to excess air causing performance issues, and the part should be replaced. If the carburetor has to be taken off for any reason, the gasket should be replaced, as it is one-time use. Installation requires a screw driver and pliers, and is rated as "Easy".