EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3267 - Instructions

All Instructions for the 3267
121 - 135 of 303

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").
1 of 3 people found this instruction helpful.
  • Linford from Cedarville, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
The floor panel of the oven was pocked and in bad shape
2 of 6 people found this instruction helpful.
  • Roger from San Juan Capistrano, CA
  • Really Easy
  • Less than 15 mins
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Was this helpful?
Thank you for voting!
oven in range would not stay lit or achieve temperature
1 of 3 people found this instruction helpful.
  • Raymond from Jersey City, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range , there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
1 of 3 people found this instruction helpful.
  • Anatoly from Palatine, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Wrench (Adjustable)
1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector). ... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people found this instruction helpful.
  • Richard from Farmington Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people found this instruction helpful.
  • mitch from brooklyn park, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people found this instruction helpful.
  • Neville from Lithonia, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people found this instruction helpful.
  • Christopher from Dearborn, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
Oven Was Dead
0 of 1 people found this instruction helpful.
  • IRIS from BROOKLYN, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is hel d on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.
Was this helpful?
Thank you for voting!
Lower burner failed to light, broiler running fine
0 of 1 people found this instruction helpful.
  • Christian from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Suc h a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Was this helpful?
Thank you for voting!
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
0 of 1 people found this instruction helpful.
  • Mark from Canton, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people found this instruction helpful.
  • Anthony from Camillus, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people found this instruction helpful.
  • Jon from Mayville, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
Oven would't heat
0 of 1 people found this instruction helpful.
  • Sidney from Hindman, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
Was this helpful?
Thank you for voting!
All Instructions for the 3267
121 - 135 of 303