3231 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter for oven not working
1 person
found this instruction helpful.
-
RONNIE from SAG HARBOR, NY
- Easy
- Less than 15 mins
-
Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person
found this instruction helpful.
-
Joe from West Winfield, NY
- Easy
- Less than 15 mins
-
Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person
found this instruction helpful.
-
Nola from Enid, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
Burners would not ignite.
1 person
found this instruction helpful.
-
Tami from Yuma, AZ
- Really Easy
- Less than 15 mins
I was looking at replacing the stove and saw the $1200.00 price tag! So I found this web site and paid $100.00 to fix my old one. It was very simple. I twisted off the old burners by sliding off the two connecting wires. Cleaned the area around the seating area of the burners. Hooked the wires on the new burners and twisted them back in
... Read more
place! Tested them to insure that was the problem and was done! Thank you for saving me $1100.00!!! Next I am getting grates so the whole stove will look band new!
Read less
Was this helpful?
Thank you for voting!
Melted electric kettle onto gas burner
2 of 4 people
found this instruction helpful.
-
Dan from Castaic, CA
- Really Easy
- Less than 15 mins
The repair was a simple replacement, no tools needed. The old burner and grate came out as easily as the new parts went in. PartSelect Customer Service Rep D. Hanham helped me find and order the correct grate. Great Customer Service!
Other Parts Used:
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person
found this instruction helpful.
-
Anita from ELKTON, VA
- Really Easy
- 15 - 30 mins
-
Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person
found this instruction helpful.
-
Jacob from LITTLE CANADA, MN
- Really Easy
- 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person
found this instruction helpful.
-
Karen from DAYTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the
... Read more
brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Read less
Was this helpful?
Thank you for voting!
Burner worn out
1 person
found this instruction helpful.
-
Robert from LORENA, TX
- Very Easy
- Less than 15 mins
Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person
found this instruction helpful.
-
FRANCES from AFFTON, MO
- Very Easy
- Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person
found this instruction helpful.
-
Gino from ARLETA, CA
- Really Easy
- Less than 15 mins
-
Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
1 person
found this instruction helpful.
-
Phyllis from BROWNVILLE, NY
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person
found this instruction helpful.
-
Mz from COLUMBIA, ME
- Very Easy
- Less than 15 mins
-
Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
Sealed burner was rusted out. Had a hole in it.
1 person
found this instruction helpful.
-
Jeanne from ELMIRA, MI
- Very Easy
- Less than 15 mins
Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!
Was this helpful?
Thank you for voting!
cap on the burner broke off
2 of 4 people
found this instruction helpful.
-
Marcia from Bronx, NY
- Really Easy
- 15 - 30 mins
-
Pliers
My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....
Was this helpful?
Thank you for voting!