EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3231 - Instructions

All Instructions for the 3231
31 - 45 of 367

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Seal was fallinig off
7 of 8 people found this instruction helpful.
  • Marilyn from Fresno, CA
  • Really Easy
  • Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people found this instruction helpful.
  • Cindy from Colton, CA
  • Really Easy
  • Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people found this instruction helpful.
  • John from Caliente, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
thermostat went out
9 of 14 people found this instruction helpful.
  • brenda from redding, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people found this instruction helpful.
  • Matt from Craig, CO
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people found this instruction helpful.
  • David from Upland, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people found this instruction helpful.
  • Charles from Kalamazoo, MI
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people found this instruction helpful.
  • Richard from Los Angeles, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
black dirty burner grates
14 of 31 people found this instruction helpful.
  • Carolyn from St. George, UT
  • Really Easy
  • Less than 15 mins
replaced grates
Was this helpful?
Thank you for voting!
burners corroed by sulphate in the gas
5 of 5 people found this instruction helpful.
  • Juan Jose from Miami, FL
  • Really Easy
  • Less than 15 mins
just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t complain, but maybe you should add the color option if there is more than one choice.

Best regards.
Was this helpful?
Thank you for voting!
Bad Door Gasket.
6 of 8 people found this instruction helpful.
  • Donald from Schuylkill Haven, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this helpful?
Thank you for voting!
One element of number display did not light
7 of 11 people found this instruction helpful.
  • Lawrence J from BENTON, AR
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-p ower on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people found this instruction helpful.
  • Charles from Old Bridge, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people found this instruction helpful.
  • Teresa from Washougal, WA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
All Instructions for the 3231
31 - 45 of 367