3222 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Starter/overload assembly and run capacitor were bad
-
Colby from Blanding, UT
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.
Was this helpful?
Thank you for voting!
fan and compressor wont start
-
JOSE from NEW YORK, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacito
... Read more
r for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,
Read less
Was this helpful?
Thank you for voting!
Smelled electrical/plastic burning. Pulled out refrigerator and noticed small flame near compressor.
-
MARTIN from RIVER FALLS, WI
- Easy
- Less than 15 mins
Unplugged refrigerator. Removed relay by unclipping wire and pulling relay off compressor. Looked-up part number and ordered part. Replaced part and plugged in refrigerator.
Was this helpful?
Thank you for voting!
Both the fridge aqnd freezer would not get cold.
-
Mary from Farmingdale, NY
- Easy
- Less than 15 mins
-
Screw drivers
Easy. Followed the video instrucations. the part was right there next to the compressor.
Was this helpful?
Thank you for voting!
Refrigerator and freezer too warm
-
Paul from Andrews, NC
- Easy
- Less than 15 mins
-
Screw drivers
1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved
... Read more
everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!
Read less
Was this helpful?
Thank you for voting!
light would not stay on
-
Kenneth from Leavenworth, KS
- Easy
- Less than 15 mins
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Was this helpful?
Thank you for voting!
the new motor was slightly larger than the old one and the bracket does not fit
-
Patricia from Oxford, MI
- Easy
- 1- 2 hours
-
Screw drivers
Had to get behind the refrigerator and clean the drain out first and that took at least and hour. Just unplug the old motor. Took the old parts of the old motor, put them on the new one and plugged it back in.
Was this helpful?
Thank you for voting!
Freezer work refierator compartment is warm
-
KIRK from Malibu, CA
- Easy
- 1- 2 hours
-
Screw drivers
Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and
... Read more
reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.
Read less
Was this helpful?
Thank you for voting!
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
-
Henry from West Seneca, NY
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Was this helpful?
Thank you for voting!
defrost timer was bad
-
Reese from Coconut Creek, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
repalaced the old one with the new one. easy
Was this helpful?
Thank you for voting!
Freezer And Frig Both Warm And Compressor Would Not Run
-
joe from decatur, GA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and
... Read more
saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.
Read less
Was this helpful?
Thank you for voting!
Refrigerator and freezer drawer would not maintain set temperature
-
James from Bel Air, MD
- A Bit Difficult
- 30 - 60 mins
-
Socket set
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I o
... Read more
rdered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.
Read less
Was this helpful?
Thank you for voting!
Refrig would not cool, freezer worked fine
-
Edward from McKinney, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Barry G was right on with instructions and expectations of the process to trouble shoot parts and how to replace. Barry also provide the right part numbers for replacement items. Thanks again Barry.
Was this helpful?
Thank you for voting!