32-27 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
glo plug wouldn/t ignite
0 of 1 people
found this instruction helpful.
-
William from Smyrna, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this helpful?
Thank you for voting!
oven would not heat up.
0 of 1 people
found this instruction helpful.
-
Paul from Warwick, RI
- Really Easy
- 15 - 30 mins
-
Nutdriver
could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!
Was this helpful?
Thank you for voting!
Oven would not light; gas odor
0 of 1 people
found this instruction helpful.
-
Emily from Conneaut, OH
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ... Read more ired our stove myself!
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ... Read more ired our stove myself!
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't get hot..smell of gas
0 of 1 people
found this instruction helpful.
-
Eric from Chicago, IL
- Easy
- 15 - 30 mins
-
Wrench (Adjustable)
Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked gre
... Read more
at.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Steve from Canton, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.
to oven igniter, but igniter was not glowing.
Was this helpful?
Thank you for voting!
Oven igniter failure
0 of 1 people
found this instruction helpful.
-
Brett from Morgantown, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in
... Read more
oven, plug in and test.
Read less
Was this helpful?
Thank you for voting!
Oven not igniting
0 of 1 people
found this instruction helpful.
-
Kirk from Saint Paul, MN
- Easy
- 15 - 30 mins
-
Wrench set
Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.
Was this helpful?
Thank you for voting!
Would turn oven on, gas smell and would not light .
0 of 1 people
found this instruction helpful.
-
Michael from Forest City, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this helpful?
Thank you for voting!
oven was slow on lite up
0 of 1 people
found this instruction helpful.
-
BILLY from DUCKHILL, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed bottom plate in oven removed three screws and cut two wires.
Was this helpful?
Thank you for voting!
Oven would not light..
0 of 1 people
found this instruction helpful.
-
Jim from Oceanside, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...
Was this helpful?
Thank you for voting!
Oven was slow to light, strong gas smell, long time to reach set temperature
0 of 1 people
found this instruction helpful.
-
Gary Warren from Alexandria, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.
It was a snap!
It was a snap!
Was this helpful?
Thank you for voting!
My oven would glow, but wouldn't heat.
0 of 1 people
found this instruction helpful.
-
Steve from Macomb, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor ... Read more by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor ... Read more by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Read less
Was this helpful?
Thank you for voting!
oven stopped lighting!!
0 of 1 people
found this instruction helpful.
-
crystal from philadelphia, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
wonderful went perfect!!!
Was this helpful?
Thank you for voting!
oven would not ignight
0 of 1 people
found this instruction helpful.
-
joseph from broadview heights, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
followed posted repair procedure on Parts select site. . . straight forward and simple. . .
Was this helpful?
Thank you for voting!
Oven And Broiler Wouldn't Light
0 of 1 people
found this instruction helpful.
-
DENNIS from HERKIMER, NY
- Difficult
- More than 2 hours
-
Screw drivers
The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.
Was this helpful?
Thank you for voting!