31MA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas was escaping from underneath the burner head
3 of 3 people
found this instruction helpful.
-
Edward from ALEXANDRIA, VA
- Easy
- 30 - 60 mins
-
Pliers
The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good
... Read more
fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.
Read less
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people
found this instruction helpful.
-
Barry from PORTERVILLE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel t
... Read more
ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Barry
Read less
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people
found this instruction helpful.
-
Isaac from LATHRUP VLG, MI
- Very Easy
- 30 - 60 mins
-
Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people
found this instruction helpful.
-
Richard from Merrimac, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
3 of 4 people
found this instruction helpful.
-
CLAREANN from THREE OAKS, MI
- Really Easy
- Less than 15 mins
don't know, my husband had it going in minutes. But I would like to say that I have ordered parts for this stove and other appliances over the years and the service is great, the parts are correct and its an easy, user friendly web site to order the parts.
Other Parts Used:
Was this helpful?
Thank you for voting!
Igniter glowed but oven would not light
2 of 2 people
found this instruction helpful.
-
Richard from West Mifflin, PA
- Easy
- Less than 15 mins
-
Nutdriver
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Was this helpful?
Thank you for voting!
Oven Was Not Getting Hot
3 of 5 people
found this instruction helpful.
-
Joe from Duarte, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people
found this instruction helpful.
-
Dominick from CLARKS SUMMIT, PA
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
2 of 2 people
found this instruction helpful.
-
James from PEORIA, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
Burner igniter problem.
2 of 2 people
found this instruction helpful.
-
Dhirajlal from SKOKIE, IL
- Really Easy
- 15 - 30 mins
-
Pliers
Replaced with a new one.
Was this helpful?
Thank you for voting!
Broken burner - easy fix
2 of 2 people
found this instruction helpful.
-
Don from NEW YORK, NY
- Really Easy
- 15 - 30 mins
-
Pliers
The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to repla
... Read more
ce. Without problems it should take about 5 minutes.
Read less
Was this helpful?
Thank you for voting!
The problem was exactly what was described on your site.
2 of 2 people
found this instruction helpful.
-
William from FREELAND, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft
... Read more
er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Tom from Greenville, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the ol
... Read more
d ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!
Read less
Was this helpful?
Thank you for voting!