EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31HG Magic Chef Range - Instructions

All Instructions for the 31HG
121 - 135 of 281

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Faulty Ignitor
0 of 1 people found this instruction helpful.
  • Emanuel from Satsuma, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason i t did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!
Was this helpful?
Thank you for voting!
Oven doesn't heat up
0 of 1 people found this instruction helpful.
  • Eric from Kohler, WI
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in . Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people found this instruction helpful.
  • MIKE from Phelan, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.
Was this helpful?
Thank you for voting!
The oven gas valve would not turn on
0 of 1 people found this instruction helpful.
  • Steve from Prospect Heights, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Replaced the oven ignitor. Toughest part was removing old screws.
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people found this instruction helpful.
  • Ron from Belleville, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people found this instruction helpful.
  • joan from florissant, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people found this instruction helpful.
  • Stephen from Evanston, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people found this instruction helpful.
  • David from Easton, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Was this helpful?
Thank you for voting!
oven did not reach temperature and was slow to heat up
0 of 1 people found this instruction helpful.
  • kevin from west pittston, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.
Was this helpful?
Thank you for voting!
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
0 of 1 people found this instruction helpful.
  • ALISE from LUDLOW, MA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took ab out 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people found this instruction helpful.
  • Jon from Mayville, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people found this instruction helpful.
  • Anthony from Camillus, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people found this instruction helpful.
  • Roger from Greenwood, AR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people found this instruction helpful.
  • Carole from Girdwood, AK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people found this instruction helpful.
  • Richard from Farmington Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.
Was this helpful?
Thank you for voting!
All Instructions for the 31HG
121 - 135 of 281