EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31HA Magic Chef Range - Instructions

All Instructions for the 31HA
106 - 120 of 303

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven making whooshing sound and not heating up
1 of 2 people found this instruction helpful.
  • Jason from Williamsburg, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 of 2 people found this instruction helpful.
  • michael from newhall, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.
Was this helpful?
Thank you for voting!
Igniter Would Glow But Stove Wouldn't Light
1 of 2 people found this instruction helpful.
  • ALAN from LUCK, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the pa rt and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people found this instruction helpful.
  • John from Racine, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
smell gas and sometimes a whoof on ignition
1 of 2 people found this instruction helpful.
  • Maynard from Knox, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .
Was this helpful?
Thank you for voting!
smell gas on oven start up
1 of 2 people found this instruction helpful.
  • Wayne from Long Grove, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
took oven tray out and loosened igniter and replace same works great.
Was this helpful?
Thank you for voting!
Oven Ignitor went to ignitor heaven.
1 of 2 people found this instruction helpful.
  • Brian from Pittsburgh, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Socket set
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I wou ld absolutely use your services again. Oven is back to working great! Thank you!
Was this helpful?
Thank you for voting!
my stovetop light did not work
1 of 2 people found this instruction helpful.
  • Geraldine M. from Fork Union, VA
  • Really Easy
  • 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this helpful?
Thank you for voting!
Oven Wouldn't Light. Smell Of Gas Before Lighting
1 of 2 people found this instruction helpful.
  • Charles from Alexandria, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out bac k first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people found this instruction helpful.
  • James from Lino Lakes, MN
  • Easy
  • Less than 15 mins
  • Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Knob numbers were almost all rubbed off
1 of 2 people found this instruction helpful.
  • Dean from Napa, CA
  • Really Easy
  • Less than 15 mins
I ordered the correct corresponding knob through PartSelect online. It came in the mail within a week. All I did was take it out of the bag and replaced the old knob with the new knob. It fit on the exact same shaft.
Was this helpful?
Thank you for voting!
Old and corroded drip pans
1 of 2 people found this instruction helpful.
  • Veronica from Miami Beach, FL
  • Really Easy
  • Less than 15 mins
Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!
Was this helpful?
Thank you for voting!
broiler pan missing
1 of 2 people found this instruction helpful.
  • RAYMOND from JACKSONVILLE, FL
  • Really Easy
  • Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people found this instruction helpful.
  • Thomas from Allison Park, PA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Needed to replace two stove valve knobs.
1 of 2 people found this instruction helpful.
  • Roberta from BROOKLYN, NY
  • Really Easy
  • Less than 15 mins
Inserting two stove valve knobs took 10 seconds! No tools necessary.
Was this helpful?
Thank you for voting!
All Instructions for the 31HA
106 - 120 of 303