31GK Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would take a very long time to warm
2 of 2 people
found this instruction helpful.
-
Barry from East Islip, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
Read less
Was this helpful?
Thank you for voting!
oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Dana from Windchester, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
The problem was exactly what was described on your site.
2 of 2 people
found this instruction helpful.
-
William from FREELAND, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft
... Read more
er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Read less
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
Continuous sparking on all burners due to broken ignition switch
2 of 2 people
found this instruction helpful.
-
Hannah from AMHERST, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
1. I accessed the burner ignition switches by lifting off stove top, sliding off burner knobs and oven knob, and removing the front switch cover (secured with 4 screws on top and 2 screws underneath).
2. I diagnosed which switch was broken: all four switches are wired together, so one faulty switch will affect sparking on both ... Read more the left and right sides of the stove. I suspected a particular switch because that burner had occasionally struggled to ignite in recent weeks and felt "loose" when turned on.
After unplugging the stove from the electrical outlet and turning on the range fan, I slid several of the switches off their gas valve stems. When comparing the suspect switch to two other switches, the suspect switch felt "loose" when rotated and didn't have the same places of resistance that the other two had.
Feeling more confident that I had found the broken switch, I used pliers to pull out the four wires connecting the suspect switch to the other switches -- it took a good bit of force, there's no convenient release. Now I could access the switch terminals, so I used a multimeter to confirm that the suspect switch didn't have any change in electrical resistance when turned on/off -- it was broken.
3. I removed the broken switch and wired its neighbors together. I plugged the stove back in and checked that this had solved the problem -- no more continuous sparking, and the other three burners still worked.
While I waited several days for the replacement switch to arrive, I reassembled everything besides the broken burner's knob (to remind me to not use that burner), and continued using the other three burners normally.
4. When the replacement switch arrived, I inserted the original four wires into the new switch's terminal holes in the original configuration (again, it took a little force), reassembled everything, and was good to go.
2. I diagnosed which switch was broken: all four switches are wired together, so one faulty switch will affect sparking on both ... Read more the left and right sides of the stove. I suspected a particular switch because that burner had occasionally struggled to ignite in recent weeks and felt "loose" when turned on.
After unplugging the stove from the electrical outlet and turning on the range fan, I slid several of the switches off their gas valve stems. When comparing the suspect switch to two other switches, the suspect switch felt "loose" when rotated and didn't have the same places of resistance that the other two had.
Feeling more confident that I had found the broken switch, I used pliers to pull out the four wires connecting the suspect switch to the other switches -- it took a good bit of force, there's no convenient release. Now I could access the switch terminals, so I used a multimeter to confirm that the suspect switch didn't have any change in electrical resistance when turned on/off -- it was broken.
3. I removed the broken switch and wired its neighbors together. I plugged the stove back in and checked that this had solved the problem -- no more continuous sparking, and the other three burners still worked.
While I waited several days for the replacement switch to arrive, I reassembled everything besides the broken burner's knob (to remind me to not use that burner), and continued using the other three burners normally.
4. When the replacement switch arrived, I inserted the original four wires into the new switch's terminal holes in the original configuration (again, it took a little force), reassembled everything, and was good to go.
Read less
Was this helpful?
Thank you for voting!
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person
found this instruction helpful.
-
june from wills point, TX
- Easy
- 15 - 30 mins
-
Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person
found this instruction helpful.
-
Michael from Syracuse, NY
- Easy
- 15 - 30 mins
-
Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an
... Read more
d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Read less
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person
found this instruction helpful.
-
ELMER from BONNEY LAKE, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
Simply remove and install new parts
1 person
found this instruction helpful.
-
Jacob from LITTLE CANADA, MN
- Really Easy
- 15 - 30 mins
Overall, it was painless and easy with zero problems
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person
found this instruction helpful.
-
RONNIE from SAG HARBOR, NY
- Easy
- Less than 15 mins
-
Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person
found this instruction helpful.
-
Brian from Spotswood, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!