EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31GG Magic Chef Range - Instructions

All Instructions for the 31GG
16 - 30 of 253

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven won't stay light
10 of 10 people found this instruction helpful.
  • Shannon from Lake Park, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Oven would not lite
11 of 14 people found this instruction helpful.
  • Timothy from Petaluma, CA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
With a little adjustment to the mount the part went in ok. Checked the oven works like new; well better than new.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people found this instruction helpful.
  • Treasure from High Point, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people found this instruction helpful.
  • Raymond from BLOOMINGTON, MN
  • Very Easy
  • Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people found this instruction helpful.
  • John from Caliente, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Door Spring Broke
7 of 9 people found this instruction helpful.
  • Thomas from Van Nuys, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
6 of 7 people found this instruction helpful.
  • Caroline from South Windsor, CT
  • Really Easy
  • Less than 15 mins
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this helpful?
Thank you for voting!
no temp control
21 of 53 people found this instruction helpful.
  • Cathreen from Lusby, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers
very easy
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Gas manifold had holes in it.
5 of 6 people found this instruction helpful.
  • Mr. J.C. from Haines City, FL
  • Really Easy
  • Less than 15 mins
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this helpful?
Thank you for voting!
Igniter Switch on the burner was constantly on
8 of 15 people found this instruction helpful.
  • Roman from West Caldwell, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
To get to the switch I had to remove the knobs and the front panel of the burner valves. There were some dozen screws, top and bottom holding the panel in-place.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacin g the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people found this instruction helpful.
  • John from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people found this instruction helpful.
  • Rachael from Adams, MA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people found this instruction helpful.
  • Michael from Secaucus, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
All Instructions for the 31GG
16 - 30 of 253