31FS-3 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven ignighter would glow, but oven would not work
0 of 1 people
found this instruction helpful.
-
graham from littleton, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this helpful?
Thank you for voting!
oven wouldn't get hot
0 of 1 people
found this instruction helpful.
-
scott from newtown, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation ar
... Read more
ound wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't light.
0 of 1 people
found this instruction helpful.
-
Roberta from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this helpful?
Thank you for voting!
Oven would'nt preheat
0 of 1 people
found this instruction helpful.
-
Ray from Valhalla, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of s
... Read more
econds!!
Read less
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people
found this instruction helpful.
-
Carl from Delano, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reco
... Read more
nnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".
Read less
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people
found this instruction helpful.
-
William from Schwenksville, PA
- Easy
- Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
Replaced burner knobs
1 of 4 people
found this instruction helpful.
-
Edison from Zuni, NM
- Easy
- Less than 15 mins
Pulled old knobs off, installed new knobs by hand, no tools used.
Was this helpful?
Thank you for voting!
Gas valve would not open
0 of 1 people
found this instruction helpful.
-
Frankie from Carlsbad, CA
- Easy
- Less than 15 mins
-
Screw drivers
I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They include
... Read more
d a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.
Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.
Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't reheat once it was on
0 of 1 people
found this instruction helpful.
-
Marc from Melville, NY
- Easy
- Less than 15 mins
-
Screw drivers
Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!
Was this helpful?
Thank you for voting!
thermostat temprature bulb hanger clips
1 of 4 people
found this instruction helpful.
-
Dwayne from Atlanta, GA
- Really Easy
- Less than 15 mins
snaped them into oven cavity attached temp bulb job complete
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people
found this instruction helpful.
-
Neville from Lithonia, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people
found this instruction helpful.
-
Christopher from Dearborn, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
My Gas Oven Wasn't Lighting and it Scared Me!
0 of 1 people
found this instruction helpful.
-
Kim from Cedar River, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.
I looked online and ordered the part. ... Read more It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.
I baked several batches of Christmas cookies and three coffee cakes the next day.
I looked online and ordered the part. ... Read more It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.
I baked several batches of Christmas cookies and three coffee cakes the next day.
Read less
Was this helpful?
Thank you for voting!