31FS-2 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven doesn't heat up
0 of 1 people
found this instruction helpful.
-
Eric from Kohler, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in
... Read more
. Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.
Read less
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people
found this instruction helpful.
-
Alan from Cinnaminson, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven wor
... Read more
ks properly. Thanx!
Read less
Was this helpful?
Thank you for voting!
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
0 of 1 people
found this instruction helpful.
-
ALISE from LUDLOW, MA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took ab
... Read more
out 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
Read less
Was this helpful?
Thank you for voting!
oven did not reach temperature and was slow to heat up
0 of 1 people
found this instruction helpful.
-
kevin from west pittston, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.
Was this helpful?
Thank you for voting!
The oven would not light even though the glow plug lit.
0 of 1 people
found this instruction helpful.
-
HELMUT from MIDDLE VILLAGE, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people
found this instruction helpful.
-
Carole from Girdwood, AK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people
found this instruction helpful.
-
Anthony from Camillus, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people
found this instruction helpful.
-
Richard from Farmington Hills, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags.
... Read more
However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Read less
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people
found this instruction helpful.
-
mitch from brooklyn park, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people
found this instruction helpful.
-
collins from Freeport, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
0 of 1 people
found this instruction helpful.
-
Dennis from East Grand Rapids, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was
... Read more
a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.
Read less
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people
found this instruction helpful.
-
Jon from Mayville, NY
- Really Easy
- 15 - 30 mins
-
Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people
found this instruction helpful.
-
Roger from Greenwood, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people
found this instruction helpful.
-
Christopher from Dearborn, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people
found this instruction helpful.
-
Neville from Lithonia, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!