EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31FS-1 Magic Chef Range - Instructions

All Instructions for the 31FS-1
106 - 120 of 263

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would take too long to light
0 of 1 people found this instruction helpful.
  • Carlos from New York, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the elec trical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.
Was this helpful?
Thank you for voting!
Faulty Ignitor
0 of 1 people found this instruction helpful.
  • Emanuel from Satsuma, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason i t did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people found this instruction helpful.
  • Stephen from Evanston, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people found this instruction helpful.
  • David from Easton, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Was this helpful?
Thank you for voting!
Oven doesn't heat up
0 of 1 people found this instruction helpful.
  • Eric from Kohler, WI
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in . Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.
Was this helpful?
Thank you for voting!
Screws in the old unit were frozen and stripped
0 of 1 people found this instruction helpful.
  • Lee from Cave Junction, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people found this instruction helpful.
  • Jon from Mayville, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people found this instruction helpful.
  • Roger from Greenwood, AR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people found this instruction helpful.
  • Carole from Girdwood, AK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
The oven would not light even though the glow plug lit.
0 of 1 people found this instruction helpful.
  • HELMUT from MIDDLE VILLAGE, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people found this instruction helpful.
  • Richard from Farmington Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people found this instruction helpful.
  • mitch from brooklyn park, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people found this instruction helpful.
  • collins from Freeport, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
0 of 1 people found this instruction helpful.
  • Dennis from East Grand Rapids, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people found this instruction helpful.
  • Anthony from Camillus, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
All Instructions for the 31FS-1
106 - 120 of 263