EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31FN-8 Magic Chef Range - Instructions

All Instructions for the 31FN-8
61 - 75 of 288

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter glowed but oven would not light
2 of 3 people found this instruction helpful.
  • edward from euclid, OH
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people found this instruction helpful.
  • Robert from Clymer, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people found this instruction helpful.
  • Donald from Peebles, OH
  • Really Easy
  • Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people found this instruction helpful.
  • Barbara L. from Tewksbury, MA
  • Really Easy
  • Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
Oven knob was broke
1 person found this instruction helpful.
  • Sara from FORT RIPLEY, MN
  • Really Easy
  • Less than 15 mins
Got the new one and put it on
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person found this instruction helpful.
  • Nola from Enid, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
new knob
2 of 4 people found this instruction helpful.
  • Marvin from Pahrump, NV
  • Really Easy
  • Less than 15 mins
Pulled one knob off and pushed the other one on.
Was this helpful?
Thank you for voting!
needed a new knob
2 of 4 people found this instruction helpful.
  • Clayton from Shortsville, NY
  • Really Easy
  • Less than 15 mins
pulled the old one off and push the new one on
Was this helpful?
Thank you for voting!
oven would not light reliably.
1 person found this instruction helpful.
  • Joe from West Winfield, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this helpful?
Thank you for voting!
Igniter for oven not working
1 person found this instruction helpful.
  • RONNIE from SAG HARBOR, NY
  • Easy
  • Less than 15 mins
  • Wrench set
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person found this instruction helpful.
  • Brian from Spotswood, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 person found this instruction helpful.
  • Larry from LAWTON, MI
  • Very Easy
  • Less than 15 mins
  • Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person found this instruction helpful.
  • FRANCES from AFFTON, MO
  • Very Easy
  • Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
unable to see the numbers on the old knob.
1 person found this instruction helpful.
  • Patricia from SAN LEANDRO, CA
  • Really Easy
  • Less than 15 mins
ordered it had to line it up then just popped it on.
Was this helpful?
Thank you for voting!
All Instructions for the 31FN-8
61 - 75 of 288