31FN-3 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not heat. Broiler was fine, just no oven.
0 of 1 people
found this instruction helpful.
-
LINDA from SALEM, OR
- Really Easy
- Less than 15 mins
-
Screw drivers
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people
found this instruction helpful.
-
kenneth from breaux bridge, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
open oven door remove bottom tray pull off two screws unplug wire remove old part install new part
Was this helpful?
Thank you for voting!
Ignitor lights but gas does not come on
0 of 1 people
found this instruction helpful.
-
Otto from Bridgeport, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. &
... Read more
completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Read less
Was this helpful?
Thank you for voting!
oven didn't get hot
0 of 1 people
found this instruction helpful.
-
Luz M. from North Providence, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
Was this helpful?
Thank you for voting!
Oven would ignite sometime, sometime not. Always argued with the broiler when it was lit first.
0 of 1 people
found this instruction helpful.
-
Audrey from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of c
... Read more
ake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!
Read less
Was this helpful?
Thank you for voting!
gas oven would not light
0 of 1 people
found this instruction helpful.
-
DAVID from HAMLIN, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.
Was this helpful?
Thank you for voting!
wall oven glowed but would not ignite
0 of 1 people
found this instruction helpful.
-
Barbara from Hacienda Heights, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!
Was this helpful?
Thank you for voting!
would not light oven
0 of 1 people
found this instruction helpful.
-
rick from chariton, IA
- Really Easy
- Less than 15 mins
-
Screw drivers
2 screws easy to remove and plug in the wire. job done.
Was this helpful?
Thank you for voting!
oven burner would not light.
0 of 1 people
found this instruction helpful.
-
Johan from Garden Grove, CA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to ... Read more the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to ... Read more the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.
Read less
Was this helpful?
Thank you for voting!
Our oven would not ignite
0 of 1 people
found this instruction helpful.
-
Randy from Redlands, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a
... Read more
brand new oven!
Read less
Was this helpful?
Thank you for voting!
Lower burner failed to light, broiler running fine
0 of 1 people
found this instruction helpful.
-
Christian from Washington, DC
- Really Easy
- Less than 15 mins
-
Screw drivers
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Suc
... Read more
h a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Read less
Was this helpful?
Thank you for voting!
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
0 of 1 people
found this instruction helpful.
-
Mark from Canton, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and
... Read more
7. re-assemble steps 3,2,1. Easy
Read less
Was this helpful?
Thank you for voting!
oven ignighter would glow, but oven would not work
0 of 1 people
found this instruction helpful.
-
graham from littleton, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this helpful?
Thank you for voting!
oven wouldn't get hot
0 of 1 people
found this instruction helpful.
-
scott from newtown, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation ar
... Read more
ound wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't light.
0 of 1 people
found this instruction helpful.
-
Roberta from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this helpful?
Thank you for voting!