EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31FB Magic Chef Range - Instructions

All Instructions for the 31FB
106 - 120 of 295

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
broiler pan missing
1 of 2 people found this instruction helpful.
  • RAYMOND from JACKSONVILLE, FL
  • Really Easy
  • Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people found this instruction helpful.
  • Thomas from Allison Park, PA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Thermostat bulb was hanging loose
2 of 5 people found this instruction helpful.
  • Willi from Old Saybrook, CT
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this helpful?
Thank you for voting!
Needed to replace two stove valve knobs.
1 of 2 people found this instruction helpful.
  • Roberta from BROOKLYN, NY
  • Really Easy
  • Less than 15 mins
Inserting two stove valve knobs took 10 seconds! No tools necessary.
Was this helpful?
Thank you for voting!
Knob numbers were almost all rubbed off
1 of 2 people found this instruction helpful.
  • Dean from Napa, CA
  • Really Easy
  • Less than 15 mins
I ordered the correct corresponding knob through PartSelect online. It came in the mail within a week. All I did was take it out of the bag and replaced the old knob with the new knob. It fit on the exact same shaft.
Was this helpful?
Thank you for voting!
Broken knob on older gas oven
1 of 2 people found this instruction helpful.
  • John from Austin, TX
  • Easy
  • Less than 15 mins
The hard part was finding the parts, this oven seemed to have a temperature control knob that required a long fitting to reach the valve stem. The set of knobs I found on PartSelect were the only ones I could find. They worked great and took about 30 seconds to put on.
Was this helpful?
Thank you for voting!
Temperature numbers were worn off the old oven knob
2 of 5 people found this instruction helpful.
  • Rena from Cedar Rapids, IA
  • Really Easy
  • Less than 15 mins
I pulled the old knob off and popped the new one on! It was easy as pie!
The shipping was amazingly fast; I ordered the part on Easter Sunday and it was on my doorstep on Tuesday! Great service!
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people found this instruction helpful.
  • James from Lino Lakes, MN
  • Easy
  • Less than 15 mins
  • Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
missing clock knob
1 of 3 people found this instruction helpful.
  • Jimmie from Hampton, VA
  • Really Easy
  • Less than 15 mins
placed knob on clock shaft with my fingers
Was this helpful?
Thank you for voting!
oven in range would not stay lit or achieve temperature
1 of 3 people found this instruction helpful.
  • Raymond from Jersey City, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range , there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.
Was this helpful?
Thank you for voting!
oven would not heat up
1 of 3 people found this instruction helpful.
  • Albert from Charlotte, TN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
it was so easy my wife could do it!!!!!!!!
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
1 of 3 people found this instruction helpful.
  • Anatoly from Palatine, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Wrench (Adjustable)
1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector). ... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
Was this helpful?
Thank you for voting!
Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").
1 of 3 people found this instruction helpful.
  • Linford from Cedarville, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
Oven would no longer ignite
0 of 1 people found this instruction helpful.
  • Karen from Hammond Ranch, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!
Was this helpful?
Thank you for voting!
All Instructions for the 31FB
106 - 120 of 295