EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31EN Magic Chef Range - Instructions

All Instructions for the 31EN
121 - 135 of 247

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven would not light even though the glow plug lit.
0 of 1 people found this instruction helpful.
  • HELMUT from MIDDLE VILLAGE, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people found this instruction helpful.
  • Richard from Farmington Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people found this instruction helpful.
  • mitch from brooklyn park, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people found this instruction helpful.
  • collins from Freeport, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
0 of 1 people found this instruction helpful.
  • Dennis from East Grand Rapids, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.
Was this helpful?
Thank you for voting!
On/off sputter of stove. Ignitor/glow bar problem.
0 of 1 people found this instruction helpful.
  • Anthony from Camillus, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this helpful?
Thank you for voting!
Oven Was Dead
0 of 1 people found this instruction helpful.
  • IRIS from BROOKLYN, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is hel d on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.
Was this helpful?
Thank you for voting!
Oven would't heat
0 of 1 people found this instruction helpful.
  • Sidney from Hindman, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
Was this helpful?
Thank you for voting!
Replaced burner knobs
1 of 4 people found this instruction helpful.
  • Edison from Zuni, NM
  • Easy
  • Less than 15 mins
Pulled old knobs off, installed new knobs by hand, no tools used.
Was this helpful?
Thank you for voting!
Gas valve would not open
0 of 1 people found this instruction helpful.
  • Frankie from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They include d a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.

Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.
Was this helpful?
Thank you for voting!
Oven wouldn't reheat once it was on
0 of 1 people found this instruction helpful.
  • Marc from Melville, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!
Was this helpful?
Thank you for voting!
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
0 of 1 people found this instruction helpful.
  • Mark from Canton, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy
Was this helpful?
Thank you for voting!
Oven wouldn't light.
0 of 1 people found this instruction helpful.
  • Roberta from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this helpful?
Thank you for voting!
Ignitor lights but gas does not come on
0 of 1 people found this instruction helpful.
  • Otto from Bridgeport, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Was this helpful?
Thank you for voting!
oven didn't get hot
0 of 1 people found this instruction helpful.
  • Luz M. from North Providence, RI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
Was this helpful?
Thank you for voting!
All Instructions for the 31EN
121 - 135 of 247