31DA Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
0 of 1 people
found this instruction helpful.
-
ALISE from LUDLOW, MA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took ab
... Read more
out 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
Read less
Was this helpful?
Thank you for voting!
Gas oven would not light.
0 of 1 people
found this instruction helpful.
-
Phillip from Prescott, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then ... Read more removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!
I then ... Read more removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!
Read less
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people
found this instruction helpful.
-
Alan from Cinnaminson, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven wor
... Read more
ks properly. Thanx!
Read less
Was this helpful?
Thank you for voting!
Oven doesn't heat up
0 of 1 people
found this instruction helpful.
-
Eric from Kohler, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in
... Read more
. Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.
Read less
Was this helpful?
Thank you for voting!
Faulty Ignitor
0 of 1 people
found this instruction helpful.
-
Emanuel from Satsuma, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason i
... Read more
t did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!
Read less
Was this helpful?
Thank you for voting!
Screws in the old unit were frozen and stripped
0 of 1 people
found this instruction helpful.
-
Lee from Cave Junction, OR
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied
... Read more
wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.
Read less
Was this helpful?
Thank you for voting!
Oven would no longer ignite
0 of 1 people
found this instruction helpful.
-
Karen from Hammond Ranch, CA
- Easy
- 30 - 60 mins
-
Screw drivers
My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then,
... Read more
somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!
Read less
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people
found this instruction helpful.
-
Neville from Lithonia, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!
Oven would't heat
0 of 1 people
found this instruction helpful.
-
Sidney from Hindman, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I ... Read more have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I ... Read more have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
Read less
Was this helpful?
Thank you for voting!
The oven would not light even though the glow plug lit.
0 of 1 people
found this instruction helpful.
-
HELMUT from MIDDLE VILLAGE, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
The oven gas valve would not turn on
0 of 1 people
found this instruction helpful.
-
Steve from Prospect Heights, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Replaced the oven ignitor. Toughest part was removing old screws.
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people
found this instruction helpful.
-
MIKE from Phelan, CA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for
... Read more
years because I didn't realize how easy the fix was.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
joan from florissant, MO
- Easy
- 15 - 30 mins
-
Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people
found this instruction helpful.
-
Roger from Greenwood, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people
found this instruction helpful.
-
Ron from Belleville, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit
... Read more
er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Read less
Was this helpful?
Thank you for voting!