31CB Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken knob on older gas oven
1 of 2 people
found this instruction helpful.
-
John from Austin, TX
- Easy
- Less than 15 mins
The hard part was finding the parts, this oven seemed to have a temperature control knob that required a long fitting to reach the valve stem. The set of knobs I found on PartSelect were the only ones I could find. They worked great and took about 30 seconds to put on.
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people
found this instruction helpful.
-
James from Lino Lakes, MN
- Easy
- Less than 15 mins
-
Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Oven Wouldn't Light. Smell Of Gas Before Lighting
1 of 2 people
found this instruction helpful.
-
Charles from Alexandria, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out bac
... Read more
k first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
Read less
Was this helpful?
Thank you for voting!
Oven ignitor would glow but took 30 - 40 mins to heat
1 of 2 people
found this instruction helpful.
-
Catherine from Newton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this helpful?
Thank you for voting!
broiler pan missing
1 of 2 people
found this instruction helpful.
-
RAYMOND from JACKSONVILLE, FL
- Really Easy
- Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
missing clock knob
1 of 3 people
found this instruction helpful.
-
Jimmie from Hampton, VA
- Really Easy
- Less than 15 mins
placed knob on clock shaft with my fingers
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
1 of 3 people
found this instruction helpful.
-
Anatoly from Palatine, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.
Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
... Read more />6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.
Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.
Read less
Was this helpful?
Thank you for voting!
oven in range would not stay lit or achieve temperature
1 of 3 people
found this instruction helpful.
-
Raymond from Jersey City, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range
... Read more
, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.
Read less
Was this helpful?
Thank you for voting!
Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").
1 of 3 people
found this instruction helpful.
-
Linford from Cedarville, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ... Read more ignition was less than 15 seconds with over one inch flame from burner.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ... Read more ignition was less than 15 seconds with over one inch flame from burner.
Read less
Was this helpful?
Thank you for voting!
oven would not heat up
1 of 3 people
found this instruction helpful.
-
Albert from Charlotte, TN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
it was so easy my wife could do it!!!!!!!!
Was this helpful?
Thank you for voting!
Burners would not light sometimes
1 of 4 people
found this instruction helpful.
-
Robert from St. Remy, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people
found this instruction helpful.
-
Stephen from Evanston, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha
... Read more
ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Read less
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people
found this instruction helpful.
-
David from Easton, PA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter
... Read more
by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Read less
Was this helpful?
Thank you for voting!
Oven would take too long to light
0 of 1 people
found this instruction helpful.
-
Carlos from New York, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.
First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the elec ... Read more trical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.
First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the elec ... Read more trical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.
Read less
Was this helpful?
Thank you for voting!
Oven doesn't heat up
0 of 1 people
found this instruction helpful.
-
Eric from Kohler, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in
... Read more
. Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.
Read less
Was this helpful?
Thank you for voting!