EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31BA Maytag Range - Instructions

All Instructions for the 31BA
121 - 135 of 244

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower burner failed to light, broiler running fine
0 of 1 people found this instruction helpful.
  • Christian from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Suc h a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Was this helpful?
Thank you for voting!
oven wouldn't get hot
0 of 1 people found this instruction helpful.
  • scott from newtown, CT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation ar ound wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Was this helpful?
Thank you for voting!
oven ignighter would glow, but oven would not work
0 of 1 people found this instruction helpful.
  • graham from littleton, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this helpful?
Thank you for voting!
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
0 of 1 people found this instruction helpful.
  • Mark from Canton, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy
Was this helpful?
Thank you for voting!
Oven wouldn't light.
0 of 1 people found this instruction helpful.
  • Roberta from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this helpful?
Thank you for voting!
Ignitor lights but gas does not come on
0 of 1 people found this instruction helpful.
  • Otto from Bridgeport, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Was this helpful?
Thank you for voting!
oven didn't get hot
0 of 1 people found this instruction helpful.
  • Luz M. from North Providence, RI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people found this instruction helpful.
  • Christopher from Dearborn, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people found this instruction helpful.
  • Neville from Lithonia, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people found this instruction helpful.
  • Carole from Girdwood, AK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people found this instruction helpful.
  • Roger from Greenwood, AR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
The oven would not light even though the glow plug lit.
0 of 1 people found this instruction helpful.
  • HELMUT from MIDDLE VILLAGE, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
Was this helpful?
Thank you for voting!
Front Burners
0 of 1 people found this instruction helpful.
  • collins from Freeport, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this helpful?
Thank you for voting!
oven would not work, broiler and range did work.
0 of 1 people found this instruction helpful.
  • Richard from Farmington Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.
Was this helpful?
Thank you for voting!
oven didnt light
0 of 1 people found this instruction helpful.
  • mitch from brooklyn park, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i removed old part, then installed new one. easy
Was this helpful?
Thank you for voting!
All Instructions for the 31BA
121 - 135 of 244