EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3167V Magic Chef - Instructions

All Instructions for the 3167V
76 - 90 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced burner
2 of 3 people found this instruction helpful.
  • Ramiro from Bernalillo, NM
  • Easy
  • Less than 15 mins
  • Wrench set
Went well
Was this helpful?
Thank you for voting!
corroded burners
2 of 3 people found this instruction helpful.
  • Daniel from Can Francisco, CA
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Unscrew the burners an install new ones! Anyone could do this.
Was this helpful?
Thank you for voting!
Original burner was eroded on the bottom and flame was coming from undernealth the burner
2 of 3 people found this instruction helpful.
  • Joe from Staten Island, NY
  • Really Easy
  • Less than 15 mins
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Was this helpful?
Thank you for voting!
The back of the knob was broken and looked bad
2 of 3 people found this instruction helpful.
  • VONDA L from BAILEY, CO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I got on-line, found your website, put in the required information (model #, brand, part, etc.) and ordered. Before ordering however, I measured, looked at the picture on-line, and compared to the part I needed. It looked right. I ordered, and the parts came in a timely manner. Got an e-mail saying they were ordered, then another e-mail s aying they were shipped. Got the parts, installed, they look so good. I'm very pleased. Thanks!
Was this helpful?
Thank you for voting!
Bad Gasket
2 of 3 people found this instruction helpful.
  • javier from Santa Ana, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person found this instruction helpful.
  • Brian from Spotswood, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person found this instruction helpful.
  • Nola from Enid, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person found this instruction helpful.
  • Karen from DAYTON, OH
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this helpful?
Thank you for voting!
igniter failed to ignite
1 person found this instruction helpful.
  • Gino from ARLETA, CA
  • Really Easy
  • Less than 15 mins
  • Socket set
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this helpful?
Thank you for voting!
Burner worn out
1 person found this instruction helpful.
  • Robert from LORENA, TX
  • Very Easy
  • Less than 15 mins
Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Sealed burner was rusted out. Had a hole in it.
1 person found this instruction helpful.
  • Jeanne from ELMIRA, MI
  • Very Easy
  • Less than 15 mins
Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person found this instruction helpful.
  • Mz from COLUMBIA, ME
  • Very Easy
  • Less than 15 mins
  • Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
cap on the burner broke off
2 of 4 people found this instruction helpful.
  • Marcia from Bronx, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers
My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....
Was this helpful?
Thank you for voting!
Burners would not lite
2 of 4 people found this instruction helpful.
  • Lloyd from Cocoa, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd
Was this helpful?
Thank you for voting!
All Instructions for the 3167V
76 - 90 of 326